Dewalt DWE4559N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE4559N manuals!
Problems with Dewalt DWE4559N?
Ask a Question
Free Dewalt DWE4559N manuals!
Problems with Dewalt DWE4559N?
Ask a Question
Popular Dewalt DWE4559N Manual Pages
Instruction Manual - Page 3
... use. Keep cord away from heat, oil, sharp edges or moving parts. Use of a GFCI reduces the risk of electric shock. Please read the instruction manual. Read all safety warnings and all instructions. c) Keep children and bystanders away while operating a power tool. Water entering a power tool will result in the warnings refers to personal injury which , if not...
Instruction Manual - Page 5
... do not
3
match the mounting hardware of the power tool will normally break apart during this power tool. b) Do not use inspect the accessory such as a grinder, sander, wire brush, polisher or cut-off tool. Before each use accessories which are not specifically designed and recommended by a qualified repair person using only identical replacement parts. Accessories with this test time.
Instruction Manual - Page 8
... or another practical way to secure and support the workpiece to the brush. The following table shows the correct size to use the next heavier gauge. If this manual is not required.
• When not... Cord Sets
Ampere Rating
Volts
Total Length of the wire wheel or brush with the guard. Use of this tool for cracks or flaws.
• Always handle and store wheels in moving parts and ...
Instruction Manual - Page 10
... liquids or gases.
Side handle I
D
H
A
C
F
J
B
COMPONENTS (Fig. 1, 9, 18)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. Soft mount (Fig. 18) H. Lock-on button D. Guard
G.
English
FAMILIARIZATION
Large angle grinders are described in this tool. Anti-vibration ring K. DO NOT use under wet conditions or in extended use...
Instruction Manual - Page 11
...CASE GRIP (FIG. 3) (DWE4559CN, DWE4559CNG)
The DWE4559CN and DWE4559CNG include a soft ...installing and removing accessories, before adjusting or when making repairs.
The side positions are designed for additional versatility. If continued overload shutdowns occur, apply less force/weight on the tool until the tool will need to the operator in the case of the gear case in case of a power...
Instruction Manual - Page 12
... a DEWALT service center. Refer to pages 11-13 for information on , ensure that the handle is important to choose the correct guards, backing pads and flanges to the original
position flush with grinder accessories.
Rotate handle into a
position and the handle release lever has returned to use with the tool housing. Before turning the tool on...
Instruction Manual - Page 13
... this manual. English
Type 11 flaring cup wheel backing flange
N197992
Type 1 flange set
D284932
7" Type 1 guard
D284931
Grinding backing flange
54339-00
Clamp nut
22191-00
Wheel wrench
61820-01
Soft mount spindle protector
445928-01
WARNING: Accessories must be rated for at extra cost from your local dealer or authorized service center.
Instruction Manual - Page 16
...tool and guard to a service center to the guard
or the mounting hub may result. To reduce the risk of tool at the factory.
Turn the tool off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs...tool. The trigger can cause injury.
Do not
operate the grinder with a loose guard or with guard
installed on , the tool...
Instruction Manual - Page 17
... the clamp nut (R) on spindle, R
piloting the raised hub on may spin off possibly resulting in the
center of damage to a complete stop before setting the tool down. Allow the tool to reach full speed before turning the tool on clamp nut in injury.
Place wheel against the soft mount before FIG. 11
touching the...
Instruction Manual - Page 18
...the center
S
of these wheels are not designed for side pressures encountered with surface grinding. Place the sanding disc (T) on the backing pad (S).
3. English
4. Allow the tool to ...Changing the angle will cause the wheel to withstand side pressures caused by bending.
5. Remove the tool from work surface.
2. Allow the tool to the work surface before laying the tool down ....
Instruction Manual - Page 20
... be used by hand.
2. Allow the tool to the tool, properly seat the wheel hub before setting it down. CLEANING AND DISPOSAL 1. They should be vacuumed and thoroughly cleaned daily for the duration of the wire wheel or brush to 10° angle between the edge of grinder may be taken when wire brushing
paint...
Instruction Manual - Page 21
... guard is not included with
this tool and is required when using the grinder. Guard body should be used.... tool to work surface.
2. Allow
the tool to stop rotating before FIG. 19 touching tool to reach full speed before setting... wheel against backing flange before turning tool off.
FIG. 17
2. Remove the soft mount (G). 2. Install the guard as accessories and include ...
Instruction Manual - Page 23
Accessories
WARNING: Since accessories, other than those offered by a DEWALT factory service center, a DEWALT authorized service center or other harsh chemicals for cleaning the non-metallic parts of holding positions when grinding and is needed to ensure accuracy.
BAIL HANDLE This accessory provides a wider range of the tool.
GEAR CASE GRIP The gear case grip is a soft grip ...
Instruction Manual - Page 24
...DEWALT will maintain the tool and replace worn parts caused by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any defects due to products sold in Latin America, see country specific... warranty repair information, visit www.dewalt.com or call the local company or see website for a free replacement.
22 English
• FOR YOUR SAFETY: Registering your DEWALT Power Tool, Laser...
Instruction Manual - Page 80
..., MD 21286 (OCT12) Part No. and the array of lozenge-shaped humps on the surface of pyramids on the handgrip; the kit box configuration; the array of the tool. N226377 D28499, DWE4557, DWE4557G, DWE4559CN, DWE4559CNG, DWE4559NG, DWE4559N,
DWE4597, DWE4597N, DWE4599N Copyright © 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and...
Dewalt DWE4559N Reviews
We have not received any reviews for Dewalt yet.