Instruction Manual
Page 3
... heat, oil, and sharp edges. • SECURE WORK. Don't use tool in presence of flammable liquids or gases. • GUARD AGAINST ELECTRIC SHOCK. Never carry tool by cord or yank it frees both hands to reduce risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS Grounding Instructions This tool should be grounded while in use face or dust mask if operation is dusty...
... heat, oil, and sharp edges. • SECURE WORK. Don't use tool in presence of flammable liquids or gases. • GUARD AGAINST ELECTRIC SHOCK. Never carry tool by cord or yank it frees both hands to reduce risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS Grounding Instructions This tool should be grounded while in use face or dust mask if operation is dusty...
Instruction Manual
Page 4
... UNINTENTIONAL STARTING. Don't carry tool with the wheel. An undersized cord will draw. The smaller the gage number, the heavier the cord. Minimum Gage for Grinders • ALWAYS USE GUARDS AND EYE SHIELDS. Before further use of checking to determine that purpose. • Do not overtighten wheel clamp nut. Have defective switches replaced by authorized service facility. Additional Safety Instructions for Cord Sets Volts Total Length of parts, mounting, and any other part that...
... UNINTENTIONAL STARTING. Don't carry tool with the wheel. An undersized cord will draw. The smaller the gage number, the heavier the cord. Minimum Gage for Grinders • ALWAYS USE GUARDS AND EYE SHIELDS. Before further use of checking to determine that purpose. • Do not overtighten wheel clamp nut. Have defective switches replaced by authorized service facility. Additional Safety Instructions for Cord Sets Volts Total Length of parts, mounting, and any other part that...
Instruction Manual
Page 5
... washers and the holes. Use this tool does not operate, check the power supply Bench Mounting 1. First install the tool rest brackets, as well. 6. Use the bolts, washers, spacers and lock nuts from this tool.A power decrease of more than 10% will cause loss of power for drilling. 4. FIG. 1 EYE SHIELD BRACKETS SPARK GUARDS EYE SHIELDS COARSE GRINDING WHEEL (36 GRIT) TOOL RESTS MEDIUM GRINDING WHEEL (60 GRIT) SWITCH (ON - Remove the drilling...
... washers and the holes. Use this tool does not operate, check the power supply Bench Mounting 1. First install the tool rest brackets, as well. 6. Use the bolts, washers, spacers and lock nuts from this tool.A power decrease of more than 10% will cause loss of power for drilling. 4. FIG. 1 EYE SHIELD BRACKETS SPARK GUARDS EYE SHIELDS COARSE GRINDING WHEEL (36 GRIT) TOOL RESTS MEDIUM GRINDING WHEEL (60 GRIT) SWITCH (ON - Remove the drilling...
Instruction Manual
Page 6
... wheels and your eyes. Operation NEVER USE A BENCH GRINDER IF IT IS NOT FIRMLY FASTENED TO A WORK BENCH OR RIGID FRAME. DW756, 3600 RPM - To turn the tool on depress the side of each eye shield by tightening the plastic knob in Fig. 4. DW756,758/385498 8/20/01 7:43 AM Page 3 English FIG. 2 TOOL REST LOCK WASHER BOLT FIG. 3 LOCK WASHER BOLT EYE SHIELD BRACKET FIG. 4 SPARK GUARD LOCK NUTS SCREWS...
... wheels and your eyes. Operation NEVER USE A BENCH GRINDER IF IT IS NOT FIRMLY FASTENED TO A WORK BENCH OR RIGID FRAME. DW756, 3600 RPM - To turn the tool on depress the side of each eye shield by tightening the plastic knob in Fig. 4. DW756,758/385498 8/20/01 7:43 AM Page 3 English FIG. 2 TOOL REST LOCK WASHER BOLT FIG. 3 LOCK WASHER BOLT EYE SHIELD BRACKET FIG. 4 SPARK GUARD LOCK NUTS SCREWS...
Instruction Manual
Page 7
... create an electrical shock hazard if not frequently cleaned out. Loosen and pull the spark guard out as far as possible. Use the washers and screws supplied. Accessories Recommended accessories for cleaning the non-metallic parts of the motor housing using compressed air is a necessary regular maintenance procedure. Remove the wheel washer and the wheel. 4 THIS TOOL HAS 1/2" ARBORS ON EACH SIDE. Changing Accessories TURN OFF THE TOOL AND DISCONNECT FROM POWER SUPPLY.
... create an electrical shock hazard if not frequently cleaned out. Loosen and pull the spark guard out as far as possible. Use the washers and screws supplied. Accessories Recommended accessories for cleaning the non-metallic parts of the motor housing using compressed air is a necessary regular maintenance procedure. Remove the wheel washer and the wheel. 4 THIS TOOL HAS 1/2" ARBORS ON EACH SIDE. Changing Accessories TURN OFF THE TOOL AND DISCONNECT FROM POWER SUPPLY.
Instruction Manual
Page 10
... both wheel washers are warranted for a full refund. Industrial Service Centers or other accessory. Install the new wheel or other qualified service organizations, These service organizations service DeWalt tools always using DeWalt replacement parts. Overtightening can crack a grinding wheel. 10.Replace the wheel cover and its screws. 11.Adjust the spark guard to 1/16" from the wheel tighten securely. 12.Adjust the tool rest to the same size. The bench grinder is found. For warranty repair information, call 1-800-4-DEWALT. DW756...
... both wheel washers are warranted for a full refund. Industrial Service Centers or other accessory. Install the new wheel or other qualified service organizations, These service organizations service DeWalt tools always using DeWalt replacement parts. Overtightening can crack a grinding wheel. 10.Replace the wheel cover and its screws. 11.Adjust the spark guard to 1/16" from the wheel tighten securely. 12.Adjust the tool rest to the same size. The bench grinder is found. For warranty repair information, call 1-800-4-DEWALT. DW756...