D-Link DGS-3120-48TC Support and Manuals
Get Help and Manuals for this D-Link item
This item is in your list!
View All Support Options Below
Free D-Link DGS-3120-48TC manuals!
Problems with D-Link DGS-3120-48TC?
Ask a Question
Free D-Link DGS-3120-48TC manuals!
Problems with D-Link DGS-3120-48TC?
Ask a Question
Popular D-Link DGS-3120-48TC Manual Pages
Product Manual - Page 9
xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Intended Readers
Typographical Conventions Notes, Notices and Cautions Safety Instructions General Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge
The DGS-3120 Series Web UI Reference Guide contains information for setup and management of the file. For example: [copy filename] means that is ...
Product Manual - Page 10
... the numbers 123 represent the IP address of the DGS-3120 Series switches can communicate directly with the Switch using the HTTP protocol. NOTE: The factory default IP address is 10.90.90.90. This will open the Web-based user interface. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Chapter 1 Web-based Switch Configuration
Introduction Login to the Web...
Product Manual - Page 16
...DGS-3120 Series Managed Switch Web UI Reference Guide
The 1000M Full_Master and 1000M Full_Slave parameters refer to connections running a 1000BASE-T cable for connection between the Switch port and other device capable of the two. This relationship is Disabled. The default...cabling. Port Description Settings
The Switch supports a port description feature where the user may name various ports...
Product Manual - Page 42
.... Session Table
Users can be enabled or disable.
Running Configuration
Under the Password Recovery option, the running configuration. This allows you to http://green.dlink.com/ for shorter cables.
When enabled, the Switch is Disabled by default. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Figure 3-14 Management Settings window
The fields...
Product Manual - Page 51
... will reveal the following window, click Management > Single IP Management > Firmware Upgrade, as show below:
Figure 3-30 Firmware Upgrade window
43
Group •
xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Add to the SIM group. Configure - To view the following dialog box for the user to enter a password for authentication from Group - Will display the SIM...
Product Manual - Page 52
... the MS resides), MAC Address, Model Name and Firmware Version. Use SNMP to the Member Switch using 'community strings', which runs locally on -board SNMP agent. The default community strings for the Switch used to upgrade configuration files from a TFTP server to a TFTP server. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Configuration File Backup/Restore
This...
Product Manual - Page 59
... can request SNMP messages. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Figure 3-39 SNMP Engine ID Settings window
The fields that can be configured ...Password, or Key. The default value is the MAC address. SNMP User Table Settings
This window displays all of this device.
The fifth octet is the MAC address of the SNMP User's currently configured on the Switch...
Product Manual - Page 222
... default password is to enable or disable the use of RADIUS Authorization. Use the drop-down menu to be enabled for the RADIUS server, which is "default...Settings window. Enter the password for MAC-based access control. Remember, the MAC list must be enabled or disabled for packets being sent requesting authentication. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide...
Product Manual - Page 224
... HTTP or HTTPS protocol.
Figure 8-27 MAC-based Access Control Local Settings - The Switch enters the authenticating stage when users attempt to access the Internet via the Switch. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide Click the Find by MAC button to locate a specific entry based on the VLAN name or ID entered. Click the...
Product Manual - Page 227
...
WAC Global State
Use this parameter to access the network via the switch. The user may choose:
Local -
xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
WAC Global Settings
Users can configure the Switch for each individual section. This is 80. The default value is the default. Choose this selection menu to enable RADIUS Authorization or not.
The...
Product Manual - Page 249
xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Figure 8-55 Login Method Lists Settings window
The Switch contains one Method List that is set and cannot be removed, yet can be authenticated using the RADIUS protocol from a remote RADIUS server.
tacacs+ - Enable Method Lists Settings
Users can be authenticated using the TACACS+ protocol from a remote TACACS+ server...
Product Manual - Page 255
... Chaining. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
To view this window, click Security > SSH > SSH Authentication method and Algorithm Settings as shown below:
Figure 8-60 SSH Authentication Method and Algorithm Settings window
The fields that can be configured for SSH Authentication Mode are described below :
Parameter
Description
Password
This may be enabled...
Product Manual - Page 298
... accept the changes made for seconds.
Transmitted (TX)
290 xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Figure 11-11 RX Error Analysis window (table)
The fields that have a good CRC.
Time Interval
Select the desired setting between 20 and 200. The default value is equal to display CRCError, UnderSize, OverSize, Fragment, Jabber, Drop...
Product Manual - Page 311
...All window
Stacking Information
To change a switch's default stacking configuration (for example, the order in the space provided and click Apply. xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Chapter 12 Save and Tools
Save Configuration / Log Stacking Information Download firmware Upload Firmware Download Configuration Upload Configuration Upload Log File Reset Reboot System...
Product Manual - Page 327
xStack® DGS-3120 Series Managed Switch Web UI Reference Guide
Appendix B Password Recovery Procedure
This document describes the procedure for resetting passwords on the Switch. This document will explain how the Password Recovery feature can be displayed to allow 2 seconds for the user needs to attach a terminal or PC with terminal emulation to use the Password Recovery feature on ...
D-Link DGS-3120-48TC Reviews
Do you have an experience with the D-Link DGS-3120-48TC that you would like to share?
Earn 750 points for your review!
We have not received any reviews for D-Link yet.
Earn 750 points for your review!