Operation Manual
Page 1
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 25759.00 Draft (01/22/08) PARTS LIST ESPAÑOL Keep this Product. SAFETY ASSEMBLY OPERATION MAINTENANCE Operator's Manual Oscillating Spindle SANDER Model No. 351.215000 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this manual with tool.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 25759.00 Draft (01/22/08) PARTS LIST ESPAÑOL Keep this Product. SAFETY ASSEMBLY OPERATION MAINTENANCE Operator's Manual Oscillating Spindle SANDER Model No. 351.215000 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this manual with tool.
Operation Manual
Page 5
...SAFETY PRECAUTIONS • Whenever adjusting or replacing any parts on the upper front right of the base. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves in any way, replace it immediately. All guards should be performed by hand for...on , always allow drum to fit Sears wet/dry vacuums. SPECIFICATIONS Spindle diameter Drum diameters 1″, 1½″, 2″ and 3″ Drum length 4½″ Spindle stroke 1″ Spindle oscillation 30 SPM Spindle speed 1725 RPM Table diameter 18″ Table height 14½″...
...SAFETY PRECAUTIONS • Whenever adjusting or replacing any parts on the upper front right of the base. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves in any way, replace it immediately. All guards should be performed by hand for...on , always allow drum to fit Sears wet/dry vacuums. SPECIFICATIONS Spindle diameter Drum diameters 1″, 1½″, 2″ and 3″ Drum length 4½″ Spindle stroke 1″ Spindle oscillation 30 SPM Spindle speed 1725 RPM Table diameter 18″ Table height 14½″...
Operation Manual
Page 6
...with each grit until it easier to fit the vacuum hose of Craftsman wet/dry vacuums. The use the correct size table insert with ... and install the desired sanding sleeve and drum for finishing of the sander. Use soap and water to Figure 10. This will make it .... KEEP TOOL IN REPAIR • If power cord is disconnected from oscillating completely, causing damage to the worm gear (Ref. Choose the size ...Apply a light coat of dust. Any attempt to repair motor may prevent the spindle from power source before attempting to remove scratches left by a qualified service technician...
...with each grit until it easier to fit the vacuum hose of Craftsman wet/dry vacuums. The use the correct size table insert with ... and install the desired sanding sleeve and drum for finishing of the sander. Use soap and water to Figure 10. This will make it .... KEEP TOOL IN REPAIR • If power cord is disconnected from oscillating completely, causing damage to the worm gear (Ref. Choose the size ...Apply a light coat of dust. Any attempt to repair motor may prevent the spindle from power source before attempting to remove scratches left by a qualified service technician...
Operation Manual
Page 7
... 2. Replace capacitor 1. Install correct fuses or circuit breakers 4. Contact Sears Service Center if necessary Adjust motor and spindle alignment MAINTENANCE 7 Defective capacitor Motor will not start ; TROUBLESHOOTING SYMPTOM Motor will not start POSSIBLE CAUSE(S) 1. Inspect... 1. Short circuit in voltage at 3. General overloading of wiring 3. Damaged or loose oscillating mechanism Excessive noise Note: Normally operating sander does make some noise Spindle and motor not aligned properly CORRECTIVE ACTION 1. Request a voltage check from the power...
... 2. Replace capacitor 1. Install correct fuses or circuit breakers 4. Contact Sears Service Center if necessary Adjust motor and spindle alignment MAINTENANCE 7 Defective capacitor Motor will not start ; TROUBLESHOOTING SYMPTOM Motor will not start POSSIBLE CAUSE(S) 1. Inspect... 1. Short circuit in voltage at 3. General overloading of wiring 3. Damaged or loose oscillating mechanism Excessive noise Note: Normally operating sander does make some noise Spindle and motor not aligned properly CORRECTIVE ACTION 1. Request a voltage check from the power...