Compaq 232007-001 - ProLiant - ML370T Support and Manuals
Get Help and Manuals for this Compaq item
This item is in your list!
View All Support Options Below
Free Compaq 232007-001 manuals!
Problems with Compaq 232007-001?
Ask a Question
Free Compaq 232007-001 manuals!
Problems with Compaq 232007-001?
Ask a Question
Popular Compaq 232007-001 Manual Pages
ProLiant ML370 Maintenance and Service Guide - Page 57
...DOS-based tool for instructions on all Compaq servers covered by this guide. DAAD collects information about the array controllers in the system and generate a list of Compaq servers still supported by this tool, visit the Compaq website: www.compaq.com
The Integrated Management Log requires Compaq Operating System-dependent drivers. For a list of detected problems.
This tool is
Array...
ProLiant ML370 Maintenance and Service Guide - Page 63
... of the memory modules must be 60 ns.
Diagnostics and Troubleshooting 3-9
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
175 - Processor
None
Configuration Invalid
180 - DC-DC Converter Failed
214 -
Replace failed assembly as indicated. xx and yy have corresponding bit set properly during installation or upgrade
Processor in slot x failed
Verify switch...
ProLiant ML370 Maintenance and Service Guide - Page 64
3-10 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
215 - Nonfunctioning
None
Voltage Regulator
Module for
Processor X no
longer redundant
216 - Tag Update
None
Rules SRAM Failure. System Halted.
220 - System Halted.
221 - Power Fault On
None
Processor Bus X
301 -
Cache accelerators not installed or ...
ProLiant ML370 Maintenance and Service Guide - Page 66
....
CPU fan has failed
Replace the failed fan.
Current SCSI
None
bus cable
configuration is not
recommended
1622 -
Primary
2S
power supply failure
1613 -
I /O Fan
2S
(Fan X) failure
detected
1611 -
3-12 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
1611 - Install the array enabler board...
ProLiant ML370 Maintenance and Service Guide - Page 67
... the drive unless all data afterward. system halted.
1703 - Back up all data before replacing
drive(s) if using
RAID 0. Diagnostics and Troubleshooting 3-13
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
1702 - SCSI cable
None
error detected; Slot x Drive
None
Array-Drive
parameter tracking
predicts imminent
failure. Ensure that the integrated SCSI controller...
ProLiant ML370 Maintenance and Service Guide - Page 68
... that the controller has detected an additional array of Array Accelerator (or controller) with one having different memory size.
continued
3-14 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
*1724 -
Press F1 to resume. This POST message will improve after the parity data has been initialized by :
Auto...
ProLiant ML370 Maintenance and Service Guide - Page 70
...compaq.com):
SCSI port (y) SCSI
ID (x)
(RESUME = F1 or F2 KEY)
1771 - Firmware update need indicated
The indicated drives are running firmware that is in progress.
Slot x drive
None
array-critical drive
firmware problem
detected-please
upgrade firmware.... 3-16 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps...
ProLiant ML370 Maintenance and Service Guide - Page 72
..., check for obstructions and check all internal connector. If the message indicates to resume. 3-18 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
1776 - Slot x Drive
None
ArrayProLiant
drive storage
enclosure problem
detected (followed by
one or more of the
following):
SCSI Port (y) Cooling fan malfunction...
ProLiant ML370 Maintenance and Service Guide - Page 74
...controller firmware to make sure drives are attached properly.
Configuration information indicates drives were configured on the original controller using Option ROMPaq. Turn off system and check SCSI cable connections to the version on a controller with newer firmware. 3-20 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible...
ProLiant ML370 Maintenance and Service Guide - Page 76
...disabled. None
Drives are not installed in their
Reinstall the drives ...replacement, repair the connection and press F2. have been replaced: SCSI port (y): SCSI ID (x). Select F2 to restart the computer with the drive array disabled.
-Or- 3-22 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
Probable Source of Problem...
ProLiant ML370 Maintenance and Service Guide - Page 80
...Upgrade Firmware Remote Utilities Diagnose Drive Array
Diagnostic error codes are located on the Compaq system partition on the Compaq SmartStart and Support Software CD. Run the Diagnostics program again. 3.
Diagnostics and Utilities are generated when the Diagnostics software recognizes a problem. 3-26 Compaq ProLiant ML370 Maintenance and Service Guide
Diagnostics Software
Test Error Codes...
ProLiant ML370 Maintenance and Service Guide - Page 90
... are many parity errors, you may need to replace the Array Accelerator board.
If the error continues, you may need to replace the Array Accelerator board. The controller will then be able to write dirty data to drives and posted write operations will then be restored. continued 3-36 Compaq ProLiant ML370 Maintenance and Service Guide
Table 3-16 ADU...
ProLiant ML370 Maintenance and Service Guide - Page 100
... tool to the setup and installation guide that is informational only. The Integrated Management Log requires Compaq operating system-dependent drivers.
3-46 Compaq ProLiant ML370 Maintenance and Service Guide
Integrated Management Log
On servers supporting the Integrated Management Display, the Compaq Integrated Management Log (IML) replaces the Critical Error Log and Correctable...
ProLiant ML370 Maintenance and Service Guide - Page 108
... the IML. The allowable settings are installed on the server support. You should load it records any information available about numerous hardware and software errors in the Compaq system partition, or the IML depending on the Compaq system partition. This allows the driver to start the operating system. This information can set the software error recovery timeout for remote...
ProLiant ML370 Maintenance and Service Guide - Page 151
...System Components Spare Parts
List 1-5 System Configuration Switch
Settings (SW2) 4-5 System Unit Specifications 5-2 tape drive, test error codes 3-34 technical support Compaq website ix telephone numbers ix technician notes viii telephone numbers Compaq Authorized
Resellers ix Compaq download facility viii technical support ix Test Computer menu option, accessing 3-26 test error codes CD-ROM 3-33...
Compaq 232007-001 Reviews
Do you have an experience with the Compaq 232007-001 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Compaq yet.
Earn 750 points for your review!