Cisco WS-X4424 - Catalyst 4000 Series 10/100/1000 BASE-T Copper Gigabit Ethernet Module Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4424 manuals!
Problems with Cisco WS-X4424?
Ask a Question
Free Cisco WS-X4424 manuals!
Problems with Cisco WS-X4424?
Ask a Question
Cisco WS-X4424 Videos
Cisco WS-X4424-GB-RJ45 $195 Price Reduction
Duration: :34
Total Views: 8
Duration: :34
Total Views: 8
Popular Cisco WS-X4424 Manual Pages
Hardware Maintenance Manual - Page 3
... be eligible for a remedy, Customer must report all warranted problems within the warranty period to the party that supplied the Product to Customer or to supply any installation, handling, maintenance, or operating instructions supplied by Cisco and Bringing the power of internetworking to the published specifications for such Software, if used in subparagraph (c) of the...
Hardware Maintenance Manual - Page 4
...Customer will supply replacement parts for the Hardware less depreciation calculated on a straight-line basis. Restricted Rights clause at Cisco's option and through a Sales or Service Partner if necessary, to either (i) provide advance replacement service as described above warranty does not apply to the restrictions as authorized by Cisco, (2) has not been installed, operated, repaired, or...
Hardware Maintenance Manual - Page 15
...the Router," includes instructions for the router installer, who should be more up to the appropriate software publication. About This Manual xv UniverCD is updated and shipped monthly, so it may be familiar with a DC-input power supply.
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures...
Hardware Maintenance Manual - Page 16
... Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory...
Hardware Maintenance Manual - Page 28
... Fiber Distributed Data Interface (FDDI)
connections.
2-6 Cisco 4000 Series Hardware Installation and Maintenance Site Log entries might need the following additional external equipment:
• Data service unit (DSU) to connect each procedure is performed on the router, update the Site Log to reflect the following :
• Installation progress-Make a copy of all actions relevant to...
Hardware Maintenance Manual - Page 32
... a Cisco 4000 series router. Network Connection Considerations
Network Connection Considerations
This section describes the considerations for each type of network connection available for more information on the media command.
2-10 Cisco 4000 Series Hardware Installation and Maintenance
Note The single-port Ethernet network processor module is not supported on the Cisco 4500-M and Cisco...
Hardware Maintenance Manual - Page 37
...module ports support synchronous connections, and the console and auxiliary ports support...support 4-Mbps rates. If you understand the electrical problems that might arise and can compensate for EIA/TIA-449 shown in the United States, supports...31
50
15
Balanced drivers allow EIA/TIA-449...setting up to 64 Kbps.
Table 2-4 lists the IEEE-recommended maximum speeds and distances for Installation...
Hardware Maintenance Manual - Page 43
...set the jumpers for the two versions of serial modules: both DTE and DCE versions of the dte-invert-timing command must also be manually changed.
This cable, available from your customer service representative, is normally ordered with the clockrate command. Note that the cables for Installation...2-23.
See the appendix "Cabling Specifications." Figure 2-23 Router Serial Cable ...
Hardware Maintenance Manual - Page 44
...-enable
2-22 Cisco 4000 Series Hardware Installation and Maintenance If the DTE device does not return SCTE, you must use the dce-terminal-timing-enable command to configure the DCE port to use a port in cable construction, temperature, and other factors can often correct this shift. Setting the Four-Port Serial Module Clock Rate...
Hardware Maintenance Manual - Page 54
... between the chassis and external devices, as a concentrator for E1
CE1 Jumper Settings The jumpers on the CE1 module set the cable impedance to a channel service unit (CSU). On the CE1, the controller provides up to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance This provides direct current (DC) isolation between the transmit or...
Hardware Maintenance Manual - Page 55
... with BNC Connectors)
H2421
Preparing for injury, jumper J2 should be set to chassis ground. For the CE1 module, four serial cables are available from Cisco Systems. All three have DB-15 connectors on the CE1end and either impedance option, a jumper installed at J2 bypasses the AC-decoupling capacitor to ground, thereby coupling the...
Hardware Maintenance Manual - Page 59
...instructions for initial startup and configuration, you must connect an EIA/TIA-232 cable between the chassis and the supporting surface for the different mounting options involve removing the front panel and component tray from the chassis shell and then installing...router, do not install the rubber feet if the chassis is to the Router
The router ships with its own set of this chapter follow...
Hardware Maintenance Manual - Page 123
...prompt (>) o enable the Break key and to default to 0x0 by setting the configuration register. Cisco 4000-M ROM Monitor C-1 A summary of whether break is configured to ...zero, you reboot the router. During the 60-second window, you can break to 0x0, you must manually...problems encountered when installing your router.
Hardware Maintenance Manual - Page 127
... help initialize the processor hardware and boot the main operating system software.
The Cisco 4500-M and Cisco 4700 ROM monitor supports more features than the familiar Cisco 4000-M ROM monitor. If you set the configuration to 0x0, you will have to manually boot the system from the console each time you can start the router in...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4424 Reviews
We have not received any reviews for Cisco yet.