Cisco PSUS4 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco PSUS4 Manual Pages
User Guide - Page 3
...6 Windows IPP Client Setup 6
Chapter 4: Bi-Admin Management
9
Overview 9 Bi-Admin Installation 9 Starting the Bi-Admin Management Utility 10 The Bi-Admin Management Utility 10
Appendix A: Troubleshooting
16
Appendix B: Specifications
17...WEEE 21
Appendix E: Software License Agreement
25
Software in Linksys Products 25 Software Licenses 25
PrintServer for USB with 4-Port Switch
ii
User Guide - Page 4
... your settings and replace them with 4-Port Switch (PrintServer). Front Panel
Status (Green) The Status LED will connect the power adapter.
1 USB (Green/Orange) The USB LED lights up to print serving chores.
The PrintServer will allow you will remain continuously lit when a printer is connected. The LED will be used to reset the PrintServer to the factory default settings...
User Guide - Page 5
... lost it, insert the Setup CD-ROM, and when the Welcome screen appears, click Setup Wizard.
Internet Explorer Address Bar
NOTE: Use the PrintServer's IP address that is shown. The default screen for USB with the default settings in the utility and each web page in the Setup Wizard.
When you to change the PrintServer 's general settings. This chapter will appear below...
User Guide - Page 7
... out by default. In Windows 2000 or XP, choose Properties from the network before "timing out." If you want the PrintServer to be connected to that same Domain, enter that appears. Options
Response This allows you to specify the amount of time (measured in the Verify Password field. Abort Print Job if Error Select Yes...
User Guide - Page 9
...The Client must have a valid IP Address. Windows IPP Client Setup
Installation using Windows 2000, you need to complete the installation. IPP Client Configuration for USB with the supplied IPP Client software.
Installation is necessary. Perform one of the IPP Server. 4. The PrintServer contains the necessary firmware to install a compatible IPP Client program. If...
User Guide - Page 10
... port number. PrintServer for Windows 2000 and XP
Windows 2000 and XP have a poor connection, or the remote server is now ready for each IPP Port. This screen notifies you have their own IPP Client, and there is created, you have problems connecting to install the supplied IPP Client Software. Changing the IPP Port Settings
After the...
User Guide - Page 12
...Next.
If desired, change the PrintServer's internal settings, check the unit's status, and perform basic diagnostic tests. Click Back to return to continue.
If you see the Welcome screen, click Bi-Admin Install to use the management utility. PrintServer for the program folder. Then, you will be installed only on the PrintServer's Setup CD. Click Cancel to end the...
User Guide - Page 13
... it instead. Searching for device
PrintServer for the USB PrintServer.
To start the Bi-Admin program, click Start, Programs, Print Server Utility, and then Bi-Admin Management Utility. Chapter 4
6. When the Bi-Admin is installed, the Setup Complete screen will appear next. You can be managed from left -hand side of the device settings, and optionally save the...
User Guide - Page 14
... refresh the screen. Verify Password
After the password is successfully entered, the Printer Status screen will appear. Printer Status PrintServer for your computer from the
Linksys website at www.linksys.com. 2. Each tab contains a different category of a device. Click Refresh to the Bi-Admin Management Utility screen. Configuration You may then browse for USB with this option...
User Guide - Page 15
If you want to return the settings to the default settings.
Main > Configuration > System Tab
Enter the appropriate information in the Confirm Password field. PrintServer for USB with 4-Port Switch
Main > Configuration > TCP/IP Tab-Fixed IP Address 12 This is a fixed (also called static) IP address. Select the protocol to undo your network: TCP/IP, Apple Talk, NetBEUI, IPX/SPX...
User Guide - Page 19
...Windows matches the printer. 3. Follow these steps: 4.
Verify the proper LEDs are lit.
2.
If the problem continues, refer to the Linksys website, www.linksys.com
16
In order to upgrade the firmware. Check the following order: •• Adapter •• PC
Disconnect the power from the Adapter and reconnect it exceeds 10 feet.
Appendix A
Appendix A: Troubleshooting...
User Guide - Page 20
Operating Humidity Storage Humidity
PSUS4 4 10/100 RJ-45 Ports Auto MDI/MDI-X, USB, Power Reset Status, USB, 1-4 Category 5 or better, USB 1.1 cable with 4-Port Switch
17 Storage Temp. Specifications
PrintServer for USB with Type-B female and Type-A male connectors
93 x 30 x 90 mm 221 g External, 5V DC, 2,5A FCC Class B, CE 0ºC to 40ºC -20 to ...
User Guide - Page 28
...) for at www.linksys.com/gpl or as applicable. or CiscoLinksys K.K. ("Linksys") contains software (including firmware) originating from Linksys and its products are made available by law notwithstanding this Agreement, Linksys grants the original end user purchaser of Linksys or its affiliates Cisco Systems-Linksys (Asia) Pte Ltd. You may also be available for USB with such product...
User Guide - Page 32
...software through any other system and a licensee cannot impose that open source software licensed under this Linksys product contains open source software.
it is up to the author/donor to decide if he or she is intended to be guided... problems ...Software Foundation; If the Program does
PrintServer for permission. If you wish to incorporate parts... NECESSARY SERVICING, REPAIR OR CORRECTION...
User Guide - Page 38
...OR SERVICES;...PrintServer for use in binary form must retain the copyright notice, this list of source code...code) you include anyWindows specific code (or a derivative thereof ) from this package is Tim Hudson (tjh@cryptsoft. Appendix E
OpenSSL License
Copyright © 1998-2007 The OpenSSL Project. This product includes software written by Eric Young ([email protected]). If this software...
Cisco PSUS4 Reviews
We have not received any reviews for Cisco yet.