Cisco NM-1FE-TX - Interface Module Ethernet Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco NM-1FE-TX manuals!
Problems with Cisco NM-1FE-TX?
Ask a Question
Free Cisco NM-1FE-TX manuals!
Problems with Cisco NM-1FE-TX?
Ask a Question
Cisco NM-1FE-TX Videos
Popular Cisco NM-1FE-TX Manual Pages
User Guide - Page 2
Feature Overview
16- The Ethernet switch network module is supported on Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. The 36-port Ethernet switch network module has 36 10/100BASE-TX ports and two optional 10/100/1000BASE-T Gigabit Ethernet ports.
This network module is a modular, high-density voice network module that provides Layer 2 switching across Ethernet ...
User Guide - Page 5
...specifications, and security violations. By default, an SVI is created for an access port. SVIs are created the first time that it does not support subinterfaces. SVIs support routing protocol and bridging configurations. it is made up of one interface to configure an SVI for Cisco 2600 Series, Cisco 3600 Series, and Cisco...function in your network. Only one or... of problems, such...
User Guide - Page 7
... switch inspects VTP messages for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
VTP Version...supported in the NM-16ESW software, VTP version 2 forwards VTP messages in each switch in the management domain when in secure mode.
• A VTP version 2-capable switch can use MAC addresses, or IP addresses; A Ethernet switch network module system supports...
User Guide - Page 9
... the client. The devices that supports the RADIUS client and 802.1x. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Device Roles With 802.1x port-based authentication, the devices in the network have specific roles as the proxy, the authentication service is then encapsulated for encapsulating and...
User Guide - Page 25
...is not supported.
If a packet enters the switch through a1 and gets switched to a2, both is not supported •... any BPDUs seen on your Ethernet switch network module can be monitored using access control lists (ACLs), ...Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
25 16- Multicast packet monitoring is configured for Cisco 2600 Series, Cisco 3600 Series, and Cisco...
User Guide - Page 31
... Weights for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Note Layer 3 IPv6 packets are serviced in Queue 2.
and 36-Port Ethernet Switch Module for Layer 2 QoS
Queue Number 3 2 1 0
CoS Value 5,6,7 3,4 2 0,1
Weight 255 64 16 1
The weights specify the number of four queues in from another. The Ethernet switch network module can construct an...
User Guide - Page 33
...a policy map by using the service-policy interface configuration command. In ...Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
33 and 36-port Ethernet switch network modules.
• System-defined masks are a part...this mode, you can include setting a specific DSCP value in QoS ACLs... the match criterion for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
...
User Guide - Page 35
16- and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
• On an ...page 96. Mapping Tables The Ethernet switch network modules support these types of service. For example, the maximum number for your network. The packets can be configured to those interfaces associated with a specific VLAN ID egressing from a host for...
User Guide - Page 36
...setting supersedes any IGMP membership reports from the table entry.
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
36
Ethernet switch network modules support a maximum of 255 IP multicast groups and support both user-defined and IGMP snooping-learned settings... forwarding table for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
associated multicast forwarding table ...
User Guide - Page 37
... them to set up a multicast... CPU. This prevents the CPU from other packets for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Joining a Multicast Group When a... 1, 2
Note that has joined the group. Figure 16 Initial IGMP Join Message
Cisco router with Ethernet switch network module
1 IGMP Report 224.1.2.3
CPU port
Multicast Forwarding
Table
88849
2
3
4
5
...
User Guide - Page 38
... 17 Second Host Joining a Multicast Group
Cisco router with Ethernet switch network module
1
CPU port Multicast Forwarding
Table
88848
2
3
4
5
Host 1 Host 2 Host 3 Host 4
Table 8 Updated Multicast Forwarding Table
Destination Address 0100.5e01.0203
Type of the interfaces. Errors in the protocol-stack implementation or in traffic for the specific multicast group. Feature Overview
16...
User Guide - Page 40
... also set the switch to shut down or to support Cisco IP phones in configuring Ethernet ports on your network. The rising threshold is different from a specific host based on the Ethernet switch network module. Alternatively, you can use port security to filter traffic destined to or received from any of the MAC addresses specified for Cisco 2600 Series, Cisco...
User Guide - Page 81
... service (TOS) bit. It also does not support filtering based on the specific keywords relative to the Cisco IP Command Reference for Cisco IOS Release 12.2.
No support for each protocol, refer to each protocol type. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
81 and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco...
User Guide - Page 108
... incremental IP telephony deployment, network managers can configure the Ethernet switch network module so that existing subnets have enough available IP addresses for the new Cisco IP phones, each of which requires a unique IP address.
• Administering a network with a VVID that there is already handled because the phone sets the Type of Service (ToS) bits in all...
User Guide - Page 166
... types of Ethernet switch network module features, use the no debug eswilp {dot1x | filtermgr | fltdrv | igmp | port-driver | power-supply | span | switch-pm}
Syntax Description
dot1x filtermgr fltdrv igmp port-driver power-supply span switch-pm
Displays ESWILP 802.1x debugging messages. Examples
The following platforms: Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers...
Cisco NM-1FE-TX Reviews
Do you have an experience with the Cisco NM-1FE-TX that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!