Cisco 12406 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 12406 Manual Pages
Configuration Guide - Page 7
... PDU 1-38 AC-Input Power Supply 1-40 DC Power Subsystem 1-42 DC PDU 1-42 DC-Input Power Entry Module 1-44 Power Distribution 1-47 Blower Module 1-47 Air Filters 1-49 Cable-Management System 1-50 Field-Replaceable Units 1-52 Technical Specifications 1-52
Preparing for Installation 2-1 Tools and Equipment 2-2 Safety and Compliance 2-2 General Safety Guidelines 2-3
Cisco 12006 and Cisco 12406 Router...
Configuration Guide - Page 9
...a DC Power Source 3-32 Power On the Router 3-35 IOS Software Configuration for the Router 3-37 Cisco IOS Software Images 3-37 Conditions to Check Before System Startup 3-38 Overview of the Boot Process 3-39 Starting the Router and Observing Initial Conditions 3-39 RP Alphanumeric LED 3-41 RP Interfaces Using the RP LEDs 3-42
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
7
Configuration Guide - Page 13
...Cisco 12406 Enhanced Series Router 6-3 Cleaning or Replacing the Air Filters 6-7 Removing and Replacing the Blower Module 6-9 Troubleshooting the Blower Installation 6-12 Removing and Replacing AC and DC Power Subsystem Components 6-13 Installation Guidelines 6-14 Power Supply and PDU Compatibility 6-14 Installing Upgrade Kits 6-17 Removing and Replacing an AC PEM 6-18 Troubleshooting the AC Power...
Configuration Guide - Page 39
... shipped by having two CSCs and two power supplies installed in place of either (or both) the second (unused) CSC slot or the second (unused) power supply bay. Nonredundant configuration that includes two CSCs and two power supplies. When you order a Cisco 12006 or Cisco 12406 Router, the nonredundant configuration is sent to all line cards, the RP, and switch fabric cards...
Configuration Guide - Page 153
... to begin configuring your environment
setup Command
One option is to use the setup command, also known as the setup command utility. OL-11497-03
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
3-49 During the first startup of an unconfigured router. Chapter 3 Installing the Router
IOS Software Configuration for the Router
Router Configuration
You can perform a basic...
Configuration Guide - Page 259
...(12000/6-AC-PDU=) Required for 1900 W power supplies. Before you must install two power supplies.
OL-11497-03
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
6-15 If you know your system power supplies and associated PDU. Do not supplies must perform a complete upgrade by replacing both power supplies, the PDU, and the blower module if you are replacing an...
Configuration Guide - Page 262
... the components of an AC power supply. Figure 6-7
AC Power Supply Components
3 1
57916
25
4
1 AC PEM 2 Handle 3 Power On/Off switch
4 Captive screws/release levers 5 AC input/DC output status indicators
6-18
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03 Before you begin this procedure, be sure to remove and replace an AC PEM from the chassis...
Configuration Guide - Page 263
... 1 Step 2 Step 3
Set the power switch to remove and replace an AC power supply. OL-11497-03
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
6-19 Chapter 6 Maintaining the Router
Removing and Replacing an AC PEM
Use the following procedure to the Off (0) position.
If you are replacing a 1400 W power supply from its AC outlet.
Unplug the power supply cord from...
Configuration Guide - Page 264
... AC Power Supply
84372
6-20
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03 Removing and Replacing an AC PEM
Chapter 6 Maintaining the Router
Step 4
Remove the PEM from the chassis (Figure 6-8): a. b.
Pivot open the levers to remove the power supply. Use two hands to eject the power supply. Slide the power supply out of its bay while supporting...
Configuration Guide - Page 265
... 12006 and Cisco 12406 Router Installation and Configuration Guide
6-21
Close the ejector levers and tighten the captive screws to securely seat the power supply to the power shelf backplane connector, do not use excessive force when inserting the power supply into the bay until it mates with its backplane connector. Chapter 6 Maintaining the Router
Removing and Replacing an AC PEM
Step...
Configuration Guide - Page 266
...indicators do not light, see the "Troubleshooting the AC Power Supply Installation" section on .
6-22
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03 The power switch is switched on page 6-22. Removing and Replacing an AC PEM
Chapter 6 Maintaining the Router
Step 6 Step 7 Step 8
Plug the power supply cable into its AC outlet.
Make sure the...
Configuration Guide - Page 270
Removing and Replacing an AC PDU
Chapter 6 Maintaining the Router
Figure 6-11
Unseating the AC Power Supply
84372
6-26
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03
Configuration Guide - Page 274
... seat the power supply to the On (1) position.
6-30
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03
for the second power supply. Removing and Replacing an AC PDU
Chapter 6 Maintaining the Router
Step 13 Reinstall the power supplies (Figure 6-15): a. Repeat steps a.
Figure 6-15
Seating the AC Power Supply
84373
Step 14 Set the power switch on...
Configuration Guide - Page 275
...
OL-11497-03
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
6-31 Figure 6-16 identifies the components of a DC power supply.
Chapter 6 Maintaining the Router
Removing and Replacing a DC PEM
The AC Input Power and DC Output Power indicators on page 6-14. If the indicators do not light, see the "Troubleshooting the AC Power Supply Installation" section on page...
Configuration Guide - Page 280
... after several attempts to power it on . Correct wiring to the DC power connector block (see Figure 6-25).
6-36
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
OL-11497-03 This indicator should light when the power switch is set to the On (1) position.
- If the Input OK indicator remains off and then on , replace the power supply with a spare.
- If the...
Cisco 12406 Reviews
We have not received any reviews for Cisco yet.