User Guide - English
Page 12
... and clean as shown (9b). WARNING: To reduce the risk of machine for a clog. Remove lower portion of the motor or a reduction in the spinning action in the vacuum cleaner. Clean the screen and check center tubes for a clog. 9. Turn power switch off and disconnect polarized plug from the cleaner by removing the...
... and clean as shown (9b). WARNING: To reduce the risk of machine for a clog. Remove lower portion of the motor or a reduction in the spinning action in the vacuum cleaner. Clean the screen and check center tubes for a clog. 9. Turn power switch off and disconnect polarized plug from the cleaner by removing the...
User Guide - English
Page 13
... or visit the website to check suction again or using the cleaner. www.bissell.com Diverter Foot Hose 2 800.237.7691 13 Check the foot hose for clogs (1). however, there will continue to clear the clog by removing the 3 screws. 2. Thermal motor protection An internal thermal protector...will not turn on or the thermal protector continues to activate, your cleaner to check for and clear the clog for floor cleaning: 1. Note: The thermal protector controls the main vacuum motor only, not the brush motor. If the cleaner will stop operating. If this happens, proceed as...
... or visit the website to check suction again or using the cleaner. www.bissell.com Diverter Foot Hose 2 800.237.7691 13 Check the foot hose for clogs (1). however, there will continue to clear the clog by removing the 3 screws. 2. Thermal motor protection An internal thermal protector...will not turn on or the thermal protector continues to activate, your cleaner to check for and clear the clog for floor cleaning: 1. Note: The thermal protector controls the main vacuum motor only, not the brush motor. If the cleaner will stop operating. If this happens, proceed as...
User Guide - English
Page 15
...shown. 5. Reposition top cover making sure to line up inside the belt and place ends into place. 5 4 Inside Tab www.bissell.com 800.237.7691 15 Recline handle for clogs or debris wrapping around the brush. 1. Turn power switch off lens. 4. Remove the bulb by pushing gently into the socket ...light bulb and remove 2 screws to lock into slots on the cover. Install the new bulb by grasping bulb and pull- 3 ing straight out of vacuum. 2 2. Maintenance and care Changing the light bulb 2 1. Replace the brush inside tab at the front with the opening is at the top and ...
...shown. 5. Reposition top cover making sure to line up inside the belt and place ends into place. 5 4 Inside Tab www.bissell.com 800.237.7691 15 Recline handle for clogs or debris wrapping around the brush. 1. Turn power switch off lens. 4. Remove the bulb by pushing gently into the socket ...light bulb and remove 2 screws to lock into slots on the cover. Install the new bulb by grasping bulb and pull- 3 ing straight out of vacuum. 2 2. Maintenance and care Changing the light bulb 2 1. Replace the brush inside tab at the front with the opening is at the top and ...
User Guide - English
Page 16
...Possible causes 1. Vacuum is in cleaner 5. Recline vacuum to cool for clearing clogs 6. Brush is twisted to the left 3. Remove obstruction or debris (pg. 14), unplug cleaner to lower setting 2. Turn dial to reset brush (pg. 14) 4. Clog in upright position...attached 5. Dirt container not installed properly 3. Filters are dirty 6. Blown fuse/tripped breaker 2. Remove handle and reinstall Vacuum cleaner won 't turn power OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting. Follow instructions...
...Possible causes 1. Vacuum is in cleaner 5. Recline vacuum to cool for clearing clogs 6. Brush is twisted to the left 3. Remove obstruction or debris (pg. 14), unplug cleaner to lower setting 2. Turn dial to reset brush (pg. 14) 4. Clog in upright position...attached 5. Dirt container not installed properly 3. Filters are dirty 6. Blown fuse/tripped breaker 2. Remove handle and reinstall Vacuum cleaner won 't turn power OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting. Follow instructions...