Manual
Page 4
motor control 22 Free-arm 23 Base-plate 24 Hinged cover The various parts of the machine • rt 10 11 12 13 14 8 7 BERNINA 6 5 II 4 3 2 1 fl a4 24 23 22 21 2 Model 807 15 16 17 18 19 20 .0" 1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 ...
motor control 22 Free-arm 23 Base-plate 24 Hinged cover The various parts of the machine • rt 10 11 12 13 14 8 7 BERNINA 6 5 II 4 3 2 1 fl a4 24 23 22 21 2 Model 807 15 16 17 18 19 20 .0" 1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 ...
Manual
Page 5
Model 810 Model 817 The various parts of the machine a 10 11 )112 im2l5im.13 14 IS 10 1 Olink•MA 5 4 3 2 L 24 22 1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-...
Model 810 Model 817 The various parts of the machine a 10 11 )112 im2l5im.13 14 IS 10 1 Olink•MA 5 4 3 2 L 24 22 1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-...
Manual
Page 30
...centre Drop feed control: sewing 1st run Stitch width: Stitch length: Automatic: Ph-2 1-11/i zigzag VWWWV (1) Do not cut off damaged part but baste the new patch on with a small zigzag. 2nd run Modern " Darning " Stitch width: 0 Stitch length: 1 Automatic: ...running t- Sew 2-5 rows of running stitch sew Stitch width: Stitch length: 4 almost 0 a straight stitch. stitch Needle position. Cul away damaged part. (Straight stitch makes the trimming 0 Needle position: centre much more easy ) Automatic: Running stitch (3) Drop feed control: sewing Always underlay a ...
...centre Drop feed control: sewing 1st run Stitch width: Stitch length: Automatic: Ph-2 1-11/i zigzag VWWWV (1) Do not cut off damaged part but baste the new patch on with a small zigzag. 2nd run Modern " Darning " Stitch width: 0 Stitch length: 1 Automatic: ...running t- Sew 2-5 rows of running stitch sew Stitch width: Stitch length: 4 almost 0 a straight stitch. stitch Needle position. Cul away damaged part. (Straight stitch makes the trimming 0 Needle position: centre much more easy ) Automatic: Running stitch (3) Drop feed control: sewing Always underlay a ...
Manual
Page 44
...man- Where a straight This will now Set zigzag onto 112/ again and care- Sew ('/o") beyond stitches. around: Where the colours overlap Top part: Complete in front of the corner. Rectangular corner: Put the needle back zigzag while sewing on . stitch, raising the presser foot and be ...sewing 'h cm 3. Then turn the material. needle in the middle of the applique ma- zigzag stitches. stitch has been used leave V) cm part. Then 1. Curves: Using the same method as possible to the straight stitched edge uncovered. Raise sew out from centre, replacing the on the ...
...man- Where a straight This will now Set zigzag onto 112/ again and care- Sew ('/o") beyond stitches. around: Where the colours overlap Top part: Complete in front of the corner. Rectangular corner: Put the needle back zigzag while sewing on . stitch, raising the presser foot and be ...sewing 'h cm 3. Then turn the material. needle in the middle of the applique ma- zigzag stitches. stitch has been used leave V) cm part. Then 1. Curves: Using the same method as possible to the straight stitched edge uncovered. Raise sew out from centre, replacing the on the ...
Manual
Page 52
... inserted properly (the ing causes: flat side of the needle must be withrawn to change needle plate). Can have c) when sewing over thick part mate- Can have the follow - d) the needle is too tight: movement. thread tension discs; c) use of the to the rear): ... causes. If breakdowns do occur then and foot starter. c) low quality needle, roughly polished. d) the hook race is damaged (call authorized Bernina dealer); If the upper thread breaks. Seam irregularities. Machine runs slowly g) hook point is clean and oiled: ing causes: 0) there are ...
... inserted properly (the ing causes: flat side of the needle must be withrawn to change needle plate). Can have c) when sewing over thick part mate- Can have the follow - d) the needle is too tight: movement. thread tension discs; c) use of the to the rear): ... causes. If breakdowns do occur then and foot starter. c) low quality needle, roughly polished. d) the hook race is damaged (call authorized Bernina dealer); If the upper thread breaks. Seam irregularities. Machine runs slowly g) hook point is clean and oiled: ing causes: 0) there are ...