Installation Manual
Page 1
Rear Parking Sensor System Model: PSS100 Installation Manual TABLE OF CONTENTS Warnings 2 Product Description 3 Packing List 3 Installation Instructions 4 Mounting the Sensors 4 Installing the Power Harness 7 Mounting the Speaker 8 Mounting the Control Module 9 Specifications 10 Maintenance 10 Troubleshooting 10 Warranty 11
Rear Parking Sensor System Model: PSS100 Installation Manual TABLE OF CONTENTS Warnings 2 Product Description 3 Packing List 3 Installation Instructions 4 Mounting the Sensors 4 Installing the Power Harness 7 Mounting the Speaker 8 Mounting the Control Module 9 Specifications 10 Maintenance 10 Troubleshooting 10 Warranty 11
Installation Manual
Page 2
high, low, and off • Three detection zones give the following warnings: 1 = slow beep within 3-5 feet 2 = medium beep within 1-3 feet 3 = steady tone within 1.3 feet • Works with 3 settings - Features • Two reversing sensors detect obstacles up to 5 feet • Upgradeable to a 4 Sensor system (requires part #: PSS200) • Includes 0° and 8° sensor sleeves to fit most bumpers • Activates only when vehicle is in reverse • Will not drain battery or void factory warranty • Includes tricolor LED/speaker display with any vehicle 1
high, low, and off • Three detection zones give the following warnings: 1 = slow beep within 3-5 feet 2 = medium beep within 1-3 feet 3 = steady tone within 1.3 feet • Works with 3 settings - Features • Two reversing sensors detect obstacles up to 5 feet • Upgradeable to a 4 Sensor system (requires part #: PSS200) • Includes 0° and 8° sensor sleeves to fit most bumpers • Activates only when vehicle is in reverse • Will not drain battery or void factory warranty • Includes tricolor LED/speaker display with any vehicle 1
Installation Manual
Page 3
... and cabling. 2. This product utilizes high voltage. You, as the driver, are not liable in full or in part for the safe operation of your vehicle and the safety of the components contained within this product will void all components with care. Excessive force used before, during or after installation that the installation of this kit. Improper installation or...
... and cabling. 2. This product utilizes high voltage. You, as the driver, are not liable in full or in part for the safe operation of your vehicle and the safety of the components contained within this product will void all components with care. Excessive force used before, during or after installation that the installation of this kit. Improper installation or...
Installation Manual
Page 4
... driver by providing an alert when an object is behind the vehicle whenever the vehicle is clear of the following items: 1. Control box with 19.68ft length of the following sensor sleeves: a. 0 degree b. 8 degree 6. Packing List The model PSS100 Rear Parking Sensor System consists of cable 3. 9-foot power cable 4. Sensors, 2 each of children and/or obstructions. Lock screw for your vehicle. Installation Manual...
... driver by providing an alert when an object is behind the vehicle whenever the vehicle is clear of the following items: 1. Control box with 19.68ft length of the following sensor sleeves: a. 0 degree b. 8 degree 6. Packing List The model PSS100 Rear Parking Sensor System consists of cable 3. 9-foot power cable 4. Sensors, 2 each of children and/or obstructions. Lock screw for your vehicle. Installation Manual...
Installation Manual
Page 5
Mounting the Sensors Choosing the Correct Sensor Sleeve Use the application guide below to verify all parts are present. This will be required. Installation Instructions Before installing this product, take time to familiarize yourself with the items in the box and use the packing list to determine whether a sensor sleeve will affect the diameter of the hole in the bumper. 4
Mounting the Sensors Choosing the Correct Sensor Sleeve Use the application guide below to verify all parts are present. This will be required. Installation Instructions Before installing this product, take time to familiarize yourself with the items in the box and use the packing list to determine whether a sensor sleeve will affect the diameter of the hole in the bumper. 4
Installation Manual
Page 6
...from slipping from the ground. c) Install the sensors equally from the center of the sensors on the rear bumper using a round metal file. Do not mount sensors directly above exhaust pipes. o Use a 26mm Hole Saw if you are using a sensor sleeve o Use a 13/16" Hole Saw if...behind the bumper to be located to check for possible obstructions, including metal braces, electrical wires, and clearance. Relocate the sensors if any obstruction exists. 2. o When drilling a metal bumper, remove the sharp edges using a grease pencil. Marking and Drilling Holes Figure 1 (2 sensors) Figure 2 (4 ...
...from slipping from the ground. c) Install the sensors equally from the center of the sensors on the rear bumper using a round metal file. Do not mount sensors directly above exhaust pipes. o Use a 26mm Hole Saw if you are using a sensor sleeve o Use a 13/16" Hole Saw if...behind the bumper to be located to check for possible obstructions, including metal braces, electrical wires, and clearance. Relocate the sensors if any obstruction exists. 2. o When drilling a metal bumper, remove the sharp edges using a grease pencil. Marking and Drilling Holes Figure 1 (2 sensors) Figure 2 (4 ...
Installation Manual
Page 7
...flush with the bumper. Many vehicles have an alignment mark on the center of the vehicle. If needed, drill a hole to the inside of the sensor. 1. Smooth edges with sleeve if required) ...connections. 6 Run the sensor wires through the factory grommet or other opening into the vehicle, taking care when drilling metal. The sensor should fit snugly into the bumper and lock into the sleeve. 3. Determine where the sensor wires will not be pinched by moving suspension parts (install power harness before using cable ties). Cable tie the sensor wires and the power harness wires...
...flush with the bumper. Many vehicles have an alignment mark on the center of the vehicle. If needed, drill a hole to the inside of the sensor. 1. Smooth edges with sleeve if required) ...connections. 6 Run the sensor wires through the factory grommet or other opening into the vehicle, taking care when drilling metal. The sensor should fit snugly into the bumper and lock into the sleeve. 3. Determine where the sensor wires will not be pinched by moving suspension parts (install power harness before using cable ties). Cable tie the sensor wires and the power harness wires...
Installation Manual
Page 8
... power harness wires with the plastic insulator. ii. iv. Installing the Power Harness Tap/Run Connection 1. Using the tap connector supplied, perform the following steps: i. iii. Make the connection between the wires by crimping down the metal connector with a pair of pliers, making sure the metal is flush with the plastic insulator. iv. b) Attach the black wire to the vehicle body or to a ground wire directly...
... power harness wires with the plastic insulator. ii. iv. Installing the Power Harness Tap/Run Connection 1. Using the tap connector supplied, perform the following steps: i. iii. Make the connection between the wires by crimping down the metal connector with a pair of pliers, making sure the metal is flush with the plastic insulator. iv. b) Attach the black wire to the vehicle body or to a ground wire directly...
Installation Manual
Page 9
... wires for the speaker to ensure good adhesion. Make sure they will not be adjusted as needed, you will install the control module. When the location is dry, peel the backing strip off the other side of the Velcro tape and press on the back of the speaker and the mounting location to the area where you should mount...
... wires for the speaker to ensure good adhesion. Make sure they will not be adjusted as needed, you will install the control module. When the location is dry, peel the backing strip off the other side of the Velcro tape and press on the back of the speaker and the mounting location to the area where you should mount...
Installation Manual
Page 10
... location. 1. The sensor must be plugged into the control module before mounting. The control module is dry, peel the backing off the Velcro pad and attach the control module. Right Side Sensor (only used in 4 sensor install) RS - When the surface is pre-fitted with Velcro for mounting. 2. LS - Plug the sensor wires, speaker and power harness into the corresponding socket (see...
... location. 1. The sensor must be plugged into the control module before mounting. The control module is dry, peel the backing off the Velcro pad and attach the control module. Right Side Sensor (only used in 4 sensor install) RS - When the surface is pre-fitted with Velcro for mounting. 2. LS - Plug the sensor wires, speaker and power harness into the corresponding socket (see...