Adaptec 2126700 - Ultra ATA Card 1233 Storage Controller Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 2126700 manuals!
Problems with Adaptec 2126700?
Ask a Question
Free Adaptec 2126700 manuals!
Problems with Adaptec 2126700?
Ask a Question
Popular Adaptec 2126700 Manual Pages
Installation Guide - Page 2
...8
Mounting ATA Disk Drives and Connecting Cables
12
Installing the Device Driver
13
Registering Your Adaptec ASH-1233 Adapter
15
This Installation Guide explains how to install the Adaptec ASH-1233 adapter, connect ATA hard disk drives to the User's Guide on the CD.
1 For more detailed installation instructions, troubleshooting tips, and support and warranty information, refer to it, and...
Installation Guide - Page 3
System Requirements
The minimum system requirements for the ASH-1233 adapter are: s Pentium II-266 MHz Processor or higher s Microsoft® Windows® 98SE, Windows Me, Windows 2000, or
Windows XP s Available PCI slot with ...
Installation Guide - Page 4
...
To successfully install your Adaptec ASH-1233 adapter and ATA disk drives, perform these tasks, in order: 1 Install the ASH-1233 adapter. (See page 4.) 2 Prepare your disk drives. (See page 7.) 3 Connect your disk drives to the ASH-1233 adapter. (See page 8.) 4 Mount your disk drives and connect the cables. (See page 12.) 5 Install the device drivers. (See page...
Installation Guide - Page 5
...: 1 Discharge any components on the back of your Adaptec ASH-1233 adapter into an existing system, back up before continuing. Installing Your Adaptec ASH-1233 Adapter
You can install your computer).
! Do not touch the gold PCI connector or any static electricity build-up all data before handling the adapter by its edges or ...
Installation Guide - Page 7
... cover screw you removed in the PCI expansion slot. Press down firmly until the adapter clicks into place. When installed properly, the adapter should appear level with Preparing Your ATA Disk Drives on page 7.
6 4 Insert the ASH-1233 adapter in Step 3. Continue with the expansion slot.
Note: Depending on your computer yet.
Installation Guide - Page 8
... Drives
If you are installing two hard disk drives, set up each drive as slave. Preparing Your ATA Disk Drives
Because setup can vary from device to device or computer to computer, always refer to your ATA disk drive and computer documentation for installation instructions, return to this document to continue with installation of the software...
Installation Guide - Page 9
... as the only device on the same cable, see page 9. Note: The Adaptec ASH-1233 adapter does not support Cable Select (CSEL) settings.
s To install two ATA disk drives on a cable, see page 11.
8 You must change the jumper settings to Master)
To connect your specific drive configuration: s To install an ATA disk drive as master or slave.
Installation Guide - Page 10
... a Cable
When you connect only one ATA disk drive to a cable, that disk drive must be set as a master drive. (See Setting Jumpers on ATA Disk Drives on page 7 for more information.) To connect one ATA drive to the ASH-1233 adapter: 1 Connect the IDE cable to an IDE connector on the ASH...
Installation Guide - Page 11
Continue with Mounting ATA Disk Drives and Connecting Cables on the right. 2 Connect the other end of the IDE cable to a master drive, as shown below on the left.
3 Repeat Step 1 and 2 to connect a second ATA disk drive to the second IDE connector on the ASH-1233 adapter, as master drives. Both disk drives must be set as shown above on page 12.
10
Installation Guide - Page 12
... Same Cable
When you connect two ATA disk drives to a cable, one disk drive must be set as the master, the other end of four ATA disk drives to your ASH-1233 adapter, as the slave. (See Setting Jumpers on ATA Disk Drives on page 7 for more information.) To connect two disk drives...
Installation Guide - Page 13
Continue with Installing the Device Driver on page 13. 12
Refer to your computer and device documentation for instructions on installing devices inside your computer.
2 Connect a power cable from your computer's power supply to each ATA disk drive in an available drive bay inside your computer. ...
Installation Guide - Page 14
s For Windows 98SE, see page 14. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your operating system (OS): s For Windows XP, see page 14. Installing the Device Driver
Before you can begin using your ASH-1233 adapter and ATA drives, you power on your computer, Windows automatically detects the new adapter and opens...
Installation Guide - Page 15
... are prompted to do so.
To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your computer if you power on your computer, Windows automatically detects the new adapter and opens the New Hardware Installation Wizard. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into your CD-ROM drive. 2 In the Wizard...
Installation Guide - Page 16
... CD during installation. Registering Your Adaptec ASH-1233 Adapter
To register your CD-ROM drive. 2 In the Wizard, click Next. 3 Click Search for the best driver..., then click Next. 4 Select CD-ROM drive, then click Next. 5 Click Next again. 6 When the installation is complete, click Finish. To complete the device driver installation: 1 Insert the Adaptec ASH-1233 CD into...
Installation Guide - Page 17
R
Adaptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA
©2004 Adaptec, Inc. AA LB 04/04 which may be registered in some jurisdictions.
Part Number: 513908-06, Ver. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. All rights reserved.
Adaptec 2126700 Reviews
We have not received any reviews for Adaptec yet.