Acer Altos S300 Support and Manuals
Get Help and Manuals for this Acer Computers item
View All Support Options Below
Free Acer Altos S300 manuals!
Problems with Acer Altos S300?
Ask a Question
Free Acer Altos S300 manuals!
Problems with Acer Altos S300?
Ask a Question
Popular Acer Altos S300 Manual Pages
User Manual - Page 2
..., with respect to their respective companies. Acer Altos S300 User's guide
Changes may be incorporated in the space provided below. All correspondence concerning your system. Model Number Serial Number Purchase Date Place of merchantability or fitness for identification purposes only and belong to the contents hereof and specifically disclaims the implied warranties of Purchase...
User Manual - Page 3
... like, nor to repair or replace any optional warranty or continuing provisions by catastrophe, fault or negligence of the user, improper or unauthorized use of the product, or use of shipment. Altos S300 Warranty
Acer warrants Altos S300 products of its manufacture to be to connectors, adapters, and other items not a part of the basic product. Acer, upon verification of...
User Manual - Page 9
... instructions
vii
1 Introduction
1
About the Altos S300 series storage array
3
Features
4
Disk drive carrier
5
Power supplies
5
Cooling system
6
I/O modules
7
Enclosure Services Module
7
Terminating Services Module
8
Concentrator Services Module
8
2 Installation precautions
9
ESD precautions
11
Safety precautions
12
Unpacking and initial setup
13
Rack installation...
User Manual - Page 10
x
Dual CSM configuration
28
Dual concentrator services modules
28
Join/Split bus jumper
30
Powering on the Altos S300 series enclosure
31
Altos S300 series jumper settings
31
Powering on an AC enclosure
32
4 System monitoring
33
Overview
35
Environmental status (ES) block
36
Features
36
Alarm buzzer mute
38
Enclosure front ...
User Manual - Page 12
The main features are described along with a list of storage arrays. This chapter introduces the Altos S300 series of the options and configurations that are available.
User Manual - Page 15
Power supplies
The Altos S300 series uses two AC power supplies for 10K RPM drives and higher (15K). The power supplies can be hot swapped. The power supplies provide active current sharing, power factor correction, over current and over voltage protection is also provided. 5
Disk drive carrier
The disk drive carrier supports a one inch...
User Manual - Page 18
... control information via the SCSI bus per the SCSI-3 Enclosure Services specification and also the SAF-TE specification. With a CSM installed in one host can be taken "off-line" without data...TSM installed in the second I /O module to a host. This means that one I/O Slot and either terminate or join the SCSI busses based on the cable configuration on how to configure your Altos S300 series...
User Manual - Page 22
... both power supply inlets before you install or operate the Altos S300. Failure to reach room ambient temperature before servicing this equipment for installation in the area of the components ...servicing.
8. Disconnect both power cables before powering on the shelf.
5. This device should be blocked, by installing a component blank or replacing the component. 12
2 Installation...
User Manual - Page 29
...Single (Joined) Bus Mode The I /O Modules are set and cannot be changed in all cases and SCSI ID 7 is reserved for the Altos S300 series enclosure are assigned. The figure below shows how the... SCSI ID's are hard set at SCSI ID 15 in any way.
The Altos S300 series enclosure has two modes ...
User Manual - Page 31
This enclosure can operate in three main configurations: Single ESM and TSM, Single CSM and TSM and Dual CSM configurations. 21
Cabling the Altos S300 series enclosure
The Altos S300 series enclosure can sense the cable arrangement and split or join the SCSI bus as appropriate. The following sections describe how to cable these configurations.
User Manual - Page 36
...4. Attach one end of each cable may be set in the 'forced split' mode to do this cable to...Power off the enclosure and the host system. 2. Replace the top cover. 4. The SCSI bus needs to...install a jumper. 3.
Attach one end of 25 meters. 26
3 Cabling and configuration
The Bus A LED will be a CSM installed in one I/O slot and a TSM in the other. The Environmental Services...
User Manual - Page 41
... both CSMs.
Remote start up
If you select this option enabled, the enclosure will power on both CSMs. Altos S300 series jumper settings
The Altos S300 series enclosure jumpers are located on the ESM and CSM (whichever is installed). Connect the cables between the enclosure and the host system. 2. To disable this feature enabled: 1. Power on...
User Manual - Page 42
... CSMs.
Powering on an AC enclosure
1. 32
3 Cabling and configuration
Delayed Start
If you select this feature, install a jumper at location JP11 on the ESM and CSM (whichever is installed). Note: Powering off the Altos S300 series enclosure also. To enable this option, the disk drives will power off all the attached host systems...
User Manual - Page 44
The location of the monitoring LEDs and how to monitor the Altos S300 Series. This chapter describes the devices used to interpret them is provided.
User Manual - Page 45
The Environmental Status block is monitored by the Environmental Status (ES) block of the Altos S300 series. 35
Overview
The Altos S300 series enclosure uses LEDs and an audible alarm to report the enclosure status. All these monitoring devices are located on the enclosure modules such as ...
Acer Altos S300 Reviews
We have not received any reviews for Acer yet.