Sennheiser NET 1 Support and Manuals
Get Help and Manuals for this Sennheiser item
View All Support Options Below
Free Sennheiser NET 1 manuals!
Problems with Sennheiser NET 1?
Ask a Question
Free Sennheiser NET 1 manuals!
Problems with Sennheiser NET 1?
Ask a Question
Sennheiser NET 1 Videos
Sennheiser Presents Net 1 For Wireless Mics
Duration: 2:09
Total Views: 416
Duration: 2:09
Total Views: 416
Watch A Demonstration Of The Sennheiser Net 1 Wireless Mic Control System At Summer NAMM 2007.
Duration: 2:01
Total Views: 1,254
Duration: 2:01
Total Views: 1,254
Popular Sennheiser NET 1 Manual Pages
Instructions for Use - Page 3
... Installing the "Wireless Systems Manager" software 15 Switching a NET 1 system on 16 Updating the firmware ...16 Operation with 3000/5000 series systems 24 Mixed operation of evolution wireless G2 series systems and 3000/5000 series systems 25 If a problem occurs 26 Problems that may occur when putting the NET 1 into operation 26 Problems that may occur during operation 27 Specifications...
Instructions for Use - Page 6
... completion of the "Wireless Systems Manager" PC software y installation manual for use of any service or repairs to this device, ask the service technician to perform safety checks to the y instructions for use of the rack-mount and portable devices y instructions for the "Wireless Systems Manager" PC software
6 Accompanying documentation
In addition to these instructions, please also refer...
Instructions for Use - Page 7
... assigning the frequencies to
the connected rack-mount devices and y wirelessly transferring data to the portable devices. The following Sennheiser systems can be configured using the NET 1:
For correct operation, only transmitters and receivers that you register on the NET 1, the WSM software and future software updates.
7
These multi-channel systems are equipped with the same...
Instructions for Use - Page 8
the firmware update software (SENNPKG file) - the instructions for use of the NET 1 y "NET" stickers to mark the receivers and transmitters that have had the
latest firmware installed after you have updated them from the supplied CD-ROM y 1 CD-ROM with EU, US and UK plug) y Device feet y 10 RJ 10 data cables y 1 RJ 45 Ethernet cable y Instructions for use of the "Wireless Systems Manager" ...
Instructions for Use - Page 10
...transfer the frequencies and settings.
10 y The MODE button is being performed.
A device is connected.
...flashes slowly: NET 1 is not the latest (see the instructions for operation
...flashes: NET 1 has been switched on the front panel of the NET 1
³·
»
¿´
º
²
LED
Color of the "Wireless Systems Manager" software). NET 1 has detected the conncted...
Instructions for Use - Page 12
...installing the device in a closed or multi-rack assembly, please note that intrinsically harmless leakage currents of the individual devices may accumulate, thereby exceeding the allowable limit value.
̈ Ground the rack via the infrared interface.
Danger of heat damage! Despite a thorough testing of the synthetics used... Putting the NET 1 into operation
Setting up the NET 1
Strong ...
Instructions for Use - Page 13
... the devices (see "Accessories/replacement parts" on the NET 1.
Make sure that within a channel bank. Note:
ƻ
For multi-channel systems, you can be connected)
When using more than eight receivers from different evolution wireless G2 series, at least one EM 3532 twin receiver
Connecting evolution wireless G2 devices
̈ Use separate RJ 10 cables to the first...
Instructions for Use - Page 14
... in the diagram below.
Connecting an EM 3532 twin receiver
̈ To connect an EM 3532 twin receiver to the sub-D socket ¹ on the NET 1, use only the right-hand (as viewed from the rear of the receiver) common data interface DATA IN/OUT as shown in which order you connect...
Instructions for Use - Page 15
... identical, so it doesn't matter in which order you have to install the "Wireless Systems Manager" software (refer to the software installation manual).
15 y Do not use a hub with NET 1 may cause network failure or other data communications problems.
̈ Then connect additional NET 1 via the sockets LAN 1 ƹ and LAN 2 Ƹ using a switch or a
router with a PC, you connect them...
Instructions for Use - Page 16
... ON/OFF switch µ to switch on how to update the firmware of the devices, please refer to the instructions for use of the software.
Updating the firmware
The NET 1 is permanently backlit in the corresponding device using the NET 1 and the "Wireless Systems Manager" software.
provided they have NET 1-compatible firmware installed can be found in the EM 3532 twin receiver must...
Instructions for Use - Page 22
... occupied or suffering from one frequency range) than free channels are connected to the NET 1.
̈ Confirm your selection by pressing the SET button.
·
»
º
³
·
Selecting a channel... with a sufficient number of free channels using the ̆/̄ rocker button (refer to the instructions for each channel bank) the number of free frequencies (channels).
Instructions for Use - Page 23
... transfer the set receiving frequency of the infrared interface ³.
To do so, proceed as described in the instructions for use of the transmitter.
̈ On the NET 1, press the...corresponding to a portable transmitter was unsuccessful, the "ERROR" LED ᕦ flashes rapidly for the next frequency range.
Cancelling the frequency scan on page 24. < 10 cm ·
¾
º
²...
Instructions for Use - Page 26
... 10 sockets (see "Connecting the devices" on page 27).
The NET 1 is disturbed. Update the firmware of the device (see "Restarting the NET 1" on page 13). The assignment of the channel buttons to the fact that the
for operation. Instead of the evolution Switch on the rack-mount device. Restart the NET 1 (see the Instructions for use original Sennheiser...
Instructions for Use - Page 27
... and cables as the PC settings. transmitters or receivers (IEM)
Update the firmware of the transmitter (see the Instructions for transferring the frequencies.
permanently
Repeat the frequency transfer (see page 20 and page 22).
Restarting the NET 1
Even if the NET 1 is disturbed.
Place the device at www.sennheiser.com/net1 and
describe the problem in front of the...
Instructions for Use - Page 30
...following measures: 1. This equipment generates, uses and can be retained as proof of either individual parts or the entire device. Increase the separation between the equipment and receiver. 3. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that is manipulated by the responsible Sennheiser service partner) you will not occur...
Sennheiser NET 1 Reviews
We have not received any reviews for Sennheiser yet.