Poulan P3816 Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan P3816 manuals!
Problems with Poulan P3816?
Ask a Question
Free Poulan P3816 manuals!
Problems with Poulan P3816?
Ask a Question
Most Recent Poulan P3816 Questions
Where Can I Find Shop Manual For P3816
My P3816 has low spark will start for about 3 seconds and stop
My P3816 has low spark will start for about 3 seconds and stop
(Posted by bham123rm 4 years ago)
What Does The Gap Set On A Poulan 3816 Ignition Module
(Posted by thomasjeff668 9 years ago)
Poulan 16 Chainsaw Manual P3816
I can get the saw to run but can't get the chain to engage. What am I doing wrong
I can get the saw to run but can't get the chain to engage. What am I doing wrong
(Posted by Mikeharder 9 years ago)
Popular Poulan P3816 Manual Pages
User Manual - Page 2
... the guide bar to prevent accidental starting when setting up, transporting, ad- Because a chain saw is a high-speed woodcutting tool, special safety precautions must
be dangerous! PLAN AHEAD S Read this manual carefully ...or making repairs except carburetor adjustments. pletely understand and can follow all safety rules, precautions, and operating instructions before using the chain saw .
User Manual - Page 3
..., marked container for an instant. S With the engine stopped, hand carry the chain saw service performed by strenuous work, check with any object such as chain saw is released. MAINTAIN YOUR SAW IN GOOD WORKING ORDER S Have all parts of the guide bar contacts any object while starting saw control. S Mix and pour fuel in a cool, dry, well ventilated place...
User Manual - Page 4
... is greater chance of kickback occurring. Follow manufacturer's chain sharpening and maintenance instructions. Check tension at the tip of the guide bar. Keep the fingers of your left hand encircling and your saw chain sharp and properly tensioned.
This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the...
User Manual - Page 5
... handles and "in-line" with CSA (Canadian Standards Association) and ANSI standards.
Kickback can be made by an authorized servicing dealer.
S Pinching the saw . A Reduced--Kickback Guide Bar has been demonstrated to the lower CKA values. The following features
are recommended. When purchasing replacement bar and chain, considerations should be caused by this manual.
User Manual - Page 6
... known to the State of California to the SERVICE section for Gasoline--Powered Chain Saws -- Turn adjusting screw on a continual and regular basis must monitor closely their physical condition and the condition of shipping spacer
3. Computed kickback angle (CKA) Table
BAR
MODEL
P/N
Length CHAIN P/N
CKA without chain brake
P3816
530044748 16″
952051211
33_
NOTE: If this...
User Manual - Page 8
... various controls and adjustments.
The chain brake activates manually if the front hand guard is too loose, it will sag below the guide bar (with the chain saw . NOTE: The chain is normal for a new chain to the full extent for cold starting . Save this manual for damage. CHOKE/FAST IDLE LEVER The choke and fast idle are set by pulling...
User Manual - Page 9
... refer to CARBURETOR ADJUSTMENT within this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand synthetic oil. FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
A 40:1 ratio is obtained by smoke coming from heat and friction. This will cause problems such as gasoline and are NOT approved for bar and chain lubri-
Use...
User Manual - Page 10
...engine still does not start after following these instructions, please call 1-800-554-6723. Slowly press... rope sharply with the saw is set the fast idle, pull the...chain brake should be replaced by an authorized service dealer if any part is worn to the full extent, the correct throttle setting for approximately 30 seconds. Repairs on how badly the unit is pushed forward, either manually...
User Manual - Page 11
... a clear retreat path
Direction of Fall
45_
FELLING LARGE TREES (6 inches (15 cm) in the desired direction of the bar hits the stump, the brake should stop immediately.
Hold the chain saw and repair or replace parts as the tree is completed, allowing the engine to fall in a particular direction include: S The wind direction and speed...
User Manual - Page 14
... chips. S Saw has to bar/chain. S Inadequate supply of damage or leaks.
To maintain guide bar:
S Move ON/STOP switch to the STOP position. S Loosen and remove bar nuts and clutch
cover. Remove bar and chain from the warranty, the operator must maintain unit as instructed in the STOP position, then clean all service and adjustments not listed in the instruction manual performed...
User Manual - Page 16
... the specifications as the chain gets duller until it dry of the chain first. Remove the cylinder cover. 3. Adjust
chain tension if necessary. ing techniques and/or depth gauge maintenance will increase the chance of the chain. WARNING: Wear protective gloves
when handling chain. The size of each year to cutting edges (side plate and top plate of the chain.
File...
User Manual - Page 17
... the top of gasohol in place and position chain saw with a flat file. See IDLE SPEED--T adjusting procedure. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). S Turn idle screw (T) clockwise to idle.
S Lightly oil external metal surfaces and
guide bar. See IDLE SPEED--T adjusting procedure. If the engine stalls, idle is...
User Manual - Page 18
...Fuel tank empty. 4. See "Difficult Starting" in the Service and Adjustments Section.
2. Install new spark plug. 5. Check for kinked or split fuel line;
Chain moves at least 5 minutes after starting.
1. Chain brake engaged. 4. Idle speed requires adjustment.
2. Clutch requires repair.
1. Empty fuel tank and refill with fuel stabilizer. S Replace spark plug with new one season to...
User Manual - Page 19
... guide bar and chain, and normal adjustments explained in the materials or workmanship of the engine causes the failure of such an emission related part, the part will repair your small off--road engine, but Poulan cannot deny warranty solely for the lack of your year 2010 and later small off --road engine owner, you should be repaired or re- Poulan...
User Manual - Page 20
... an Poulan authorized repair center as soon as defined in the instruction manual. RANTY SERVICE: Warranty services or repairs shall be liable for damages to other engine components caused by the use of add-on or modified parts. Call: 1--800--554--6723 or send e-mail correspondence to cover failures of
warranted parts caused by the failure of "repair or replace as...
Poulan P3816 Reviews
We have not received any reviews for Poulan yet.