Pfaff hobbylock 785 Support and Manuals
Get Help and Manuals for this Pfaff item
View All Support Options Below
Free Pfaff hobbylock 785 manuals!
Problems with Pfaff hobbylock 785?
Ask a Question
Free Pfaff hobbylock 785 manuals!
Problems with Pfaff hobbylock 785?
Ask a Question
Popular Pfaff hobbylock 785 Manual Pages
Owner's Manual - Page 1
II. 747! instruction manual
i;
I
V
Owner's Manual - Page 2
... but an authorized agent.
C)
The maximum approved the light bulb is 15 watts. adjusted Pfaff
Notes on safety
A) aatoOhvrfeweotaihidunecsgioenntrnjoeutmeirntydhuuleaseotnsuudtspaalnykoadebnwsdstehhuridelfvefoeiuwcspietnehpwneemitrnscgoeka.vwnreieifmnegt,eont
B) When leaving the machine,
changing parts or machine must never be
accessories, disconnected
the
from the power source.
Owner's Manual - Page 4
...sewing light Foot control Notes on safety Installing the thread spool stand Opening the looper cover Threading guide wires 18 and the thread guides behind the carrying handle . 4-thread overedge... knife Oiling the machine Sewing problems and their removal Accessories Thread spool net/thread unreeling disc Specifications Contents of the upper knite Setting the standard thread tensions Correcting the...
Owner's Manual - Page 5
...cover 8 Lint box 9 Handwheel 10 Looper cover with recess 11 Upper knife 12 Work support (swivel-type) 13 Needle plate 14 Sewing foot 15 Needle bar 16 Sewing foot lifting lever 17 Thread ...spool holder 18 Thread guides 19 Thread guide bar 20 Machine socket 21 Master switch 22 Rear thread guide (4 x) 23 Differential feed adjustment knob 24 Accessory box 25 ...
Owner's Manual - Page 7
.... D) The drive belt must never be pre-selected in two steps by anyone but an authorized Pfaff agent.
5
Electronic foot control
Maximum speed can be adjusted by the switch on safety A) Owing...avoid injury and observe the sewing area continuously while sewing. B) When leaving the machine, changing parts or accessories, the machine must take sufficient care to the up and down , the faster ...
Owner's Manual - Page 13
looper cover 10. I
Seam allowance
If the cutting is guided along below
1 the lint box, use the
I -J
/
/
Inserting the lint box:
downwards the cover. Then push the bottom of the box against the machine.
I
After threading the machine, push handle
2 down, and close work support 12 and
-
Owner's Manual - Page 20
...-length adjustment knob 25 at the stitch length desired between 1 and 4 mm.
Standard setting N is3mm.
/
/ -
/
c\L-_ t/>7 A . .i,___c(
Setting the stitch length on the hobbylock 784 without differential feed
Open work support 12. Material
Light materials: Organdy, light-knit fabric, Taffeta, silk, lining materials Medium-heavy materials: Cotton, tricot, linen, dress materials Heavy...
Owner's Manual - Page 21
... to process (see table on the hobbylock 786 The differential feed prevents inter-ply shift. Set the diffe rential feed according to the material you wish to obtain fashionable effects on garments:...more by the front feed dog than by the rear one behind the other, which both feed dogs Setting 1.5 = Long stroke of front feed dog, short stroke of 1.5-2 when light fabrics are accomplished.
...
Owner's Manual - Page 22
... of differential feed
Illustration
0.5 to be set during sewing.
Setting of the differential feed. The differential feed can also be made. N
1
Correct seam
a
Fabric
Nylon, tricot, lining fabrics..., ve elastic fabrics, rib stitch goods
Fig. 1
C
Fig. 2
Fig. 3 20
Fig. 4 In order to make sure about the setting required for the fabric you wish to process, a sewing test has to -
Owner's Manual - Page 23
...the seam width
c
The standard seam width setting is
marked with adjusting knob 26.
Set the upper knife at its basic position again and close the looper cover.
Open work support 12 and looper cover 10. cA
-...the seam width, it forwards until pin A engages in the hole of the axial upper knife guide fully to 5. Disengage the upper knife according to re-adjust the thread tension.
21 When ...
Owner's Manual - Page 27
...Threading path:
polyester thread
1. right looper, red path
2. 3,
left looper, yellow path needle thread, green path
For threading of needle and loopers,
Tension setting: RYGeerldeloetwnhrttehharrdeeaatddenttseeinnossnii,oonnri,,gnhletefetlodloolepoeptrherread
see
pages
7
to
polyester thread 11. "N"
flat edge, Fig. Depending on material and thread, the
round edge, Fig. I
Rolled...
Owner's Manual - Page 28
...Use the needle change tool. Then push the needle up into the needle holder as far as spare parts. LM
I K
Inserting the needle
Insert the needle in hole M of the needle change tool in...screw driver. Turn the hand wheel in hole M of the arrow until the needle bar is at its highest position. Loosen the set screw securely.
An incorrectly inserted needle will go.
Tighten needle set screw...
Owner's Manual - Page 29
___ I -
N'
1[ Insert the new upper knife and tighten its lowest
27 I
-
-
/
Changing the upper knife:
Pull out the mains plug.
L_--- Turn the handwheel
/
until the upper knife is at its retaining screw securely.
.
Unscrew the knife retaining screw and remove upper knife. Set upper knife with knife guide 27 up
(cutting position).
Owner's Manual - Page 32
...
Incorrectly threaded.
Incorrect stitch formation
Incorrect setting of differential feed.
Sewing problems of the kind described below . and operation errors.
Puckered seams 30
Thread tension too ..., and there are no difficult adjustments to be corrected by following the instructions below may occur due to incorrect threading. Thread has caught. Thread correctly...
Owner's Manual - Page 34
Specifications:
Maximum sewing speed Seam width Stitch length
Sewing foot Lubrication Sewing foot height Needle system Number of threads Dimensions Weight
Contents of cardboard box
1 machine with motor 1 foot control 1 instruction manual/guarantee certificate 1 lint box 1 thread spool stand 4 thread spool stand bars 1 thread guide 1 machine cover
1.300 stitches/mm. 3-7.2mm 1 -4 mm (HL-786) 1 -5...
Pfaff hobbylock 785 Reviews
We have not received any reviews for Pfaff yet.