NEC X474HB Support and Manuals
NEC X474HB Videos
Popular NEC X474HB Manual Pages
External Control Codes - Page 20
... ETX (03h): End of Message
Check code BCC: Block Check Code Refer to support this operation. The monitor replies with the current brightness setting and capability
to support this byte is set to change the "Backlight" setting.
No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the OP code page 0). Message STX (02h): Start of...
External Control Codes - Page 21
... is 18 bytes. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10 bytes. Message STX (02h): Start of packet
Delimiter CR
Step 4.
Ex.) When this byte is set to check the Backlight setting. (Recommended) Step 5. ETX (03h): End of packet
Step 3. Header SOH-'0'-'0'- Ex.) If Monitor ID is '1', specify 'A'. '0' (30h...
External Control Codes - Page 23
...(in the page 2). Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code. The monitor replies for reading the temperatures from the sensors. Monitor ID: Indicates a replying Monitor ID. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 10 bytes. 6.2.
Step 1. MultiSync P402 /P462 /P552 /P702 /V422 /V462 /V551 /V651 /V322 /V652 /V552...
External Control Codes - Page 24
...): Message length is 25 degrees Celsius.
(24/72)
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is the controller.
The controller requests the monitor to 'A', the replying Monitor ID is '1'.
'D' (44h): Message Type is "Get parameter reply".
'1'-'2' (31h, 32h): Message length is set to send the temperature from the selected sensor...
External Control Codes - Page 26
...
Item
Backlight Contrast Sharpness Brightness Hue Color Color Temperature Color control
Gamma Correction
Movie
Adaptive
Settings Contrast
Noise Reduction
Telecine
Picture mode
OP OP code Parameter
cod
e
pag
e
00h 10h
0: dark
|
100(64h): bright
00h 12h
0: low
|
100(64h): high
00h 8Ch
0: dull
|
24(18h): sharp
00h 92h
0: dark
|
100(...
External Control Codes - Page 35
...Auto Setup
00h 1Eh
1: Execute
TV-Channel UP/DOWN
00h 8Bh
0: No Action 1: Up 2: Down
Select sensor
Temperature 02h 78h
1: Sensor #1 2: Sensor #2 3: Sensor #3
Readout a temperature 02h 79h
Returned value is complement. Momentary
Momentary
This
operation
requires supported
... 0: | 65535:
Remarks
This operation has
limitation
of
selection. Refer to the monitor
instruction
manual.
External Control Codes - Page 38
... controller requests the monitor to the section 4.5 "Check code" for a BCC calculation.
No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command The monitor replies same as power control command to the controller. '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode 0001: ON 0002, 0003: Do not set to 'A', the replying Monitor ID is '1'. 'B' (42h...
External Control Codes - Page 42
... '0' (34h and 30h). Ex.) When this byte is set to write Asset data. Data(0) -- Monitor ID: Indicate a replying Monitor ID. 8.2 Asset Data write
This command is used in which you want to the monitor at a time is 32bytes. ETX (03h): End of the Asset data area.
No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write...
External Control Codes - Page 68
... of which you want to the section 4.5 "Check code" for Pass codes inputs, then it only checks Pass cords (and releases image muting if Pass codes are matched with them then setting isn't changed, and reply error status and a current condition. If codes aren't matched with monitor resisted pass codes, then this command while waiting for a BCC calculation...
Specification Brochure - Page 2
... LCD...definition panel allows for rugged 24/7 use, the NEC X474HB is never an accident. Meeting the requirements for ...any condition
• Two port LAN hub simplifies installation and monitoring of deployed displays
• Localized Dimming Function ...smooth video and crisp imagery. The X474HB includes:
• Open Pluggable Specification and Interface Expansion slots offer the flexibility...
Launch Press Release - Page 1
... other professional large-screen displays -
The 47-inch specialty LCD display is designed to cope with the durability and readability challenges that often arise in shopping windows or cabinets for NEC Display Solutions) (312) 673-6054 [email protected]
NEC DISPLAY SOLUTIONS SETS NEW BENCHMARK WITH SUNLIGHTREADABLE PROFESSIONAL MULTISYNC X474HB DISPLAY
Innovative Large-Screen Display...
User's Manual - Page 27
... signal is restarted. The factory preset password is selected. AUTO
IP ADDRESS:
Set your IP address of the network connected to the monitor when "MANUAL" is selected for [IP SETTING].
192.168.0.10
SUBNET MASK:
Set your subnet mask number of the network connected to the monitor when "MANUAL" is selected for [IP SETTING].
255.255.255.0
DEFAULT GATEWAY...
User's Manual - Page 34
...le is called "External_control.pdf".
1) Interface
PROTOCOL BAUD RATE DATA LENGTH PARITY BIT STOP BIT FLOW CONTROL
RS-232C 9600 [bps] 8 [bits] NONE 1 [bit] NONE
This LCD monitor uses RXD, TXD and...page 49 "2) RS-232C input/output". Connection LCD Monitor + PC
MultiSync
PC
RS-232C
RS-232C Cable
NOTE:
If your dealer for RS-232C control. Instructions for the control command can be used for...
User's Manual - Page 43
... must be affected even when [RESET] is model name.
Up to the monitor. PJLink PASSWORD Set a password for HTTP server. This standard protocol is a standardization of protocol used . Type in 2005. However, if you forget your password, consult with your password.
The device supports all the commands of PJLink Class 1. Setting of PJLink will not be 10 characters or...
NEC X474HB Reviews
Do you have an experience with the NEC X474HB that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!