JET Tools 5SS-1C-15 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools 5SS-1C-15 manuals!
Problems with JET Tools 5SS-1C-15?
Ask a Question
Free JET Tools 5SS-1C-15 manuals!
Problems with JET Tools 5SS-1C-15?
Ask a Question
Popular JET Tools 5SS-1C-15 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Electric Hoist
Models SS-1C, SS-3C
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-121100 Revision F1 08/2014 Copyright © 2014 JET
User Manual - Page 2
...APPLY TO YOU. Parts; Woodworking Machinery used for commercial or industrial purposes default to applicable state law. Manual Hoists; Warranty and Service
JET warrants every product ...specific legal rights, subject to a Two Year Warranty. Woodworking Machinery Limited Lifetime - Shop Tools; More Information JET is a division of an Authorized Service Center in your product or on the JET...
User Manual - Page 4
... not install this ...be moved. 15. If
you ... have the same capacity as set " over people. Avoid swinging...repaired or replaced. 14. Replace the warning labels if they are not familiar with twisted, kinked, worn or otherwise damaged chain. this chain hoist for other purposes, JET.... 7. Do not operate this manual. Do not use by a ...a qualified Walter Meier service center. 20. Warn ...
User Manual - Page 5
... installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Model SS-3C features single lift speed, 230/460V three-phase power requirement.
If there are available in a variety of trouble-free operation if used in this manual.
JET can also be reached at our web site: www.jettools.com.
Contact your specifications. Model SS-1C...
User Manual - Page 6
...10.24 4.43 9.45 20.16
1SS-1C 1 2SS-1C 2 3SS-1C 3 5SS-1C 5
19.70 9.80 6.60 4.90
24.41 28.15 31.5 30.71
H3
1
1.74HP, (...15 min/hr.
Single Phase
Available in .)
Motor
Duty Cycle Rating
No. Specifications -
The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, JET reserves the right to change specifications...
User Manual - Page 7
... in .)
Motor
Duty Cycle Rating
No. Rated Model Cap'y
(ton)
1/2SS-3C 1/2
1SS-3C 1 2SS-3C 2 3SS-3C 3 5SS-3C 5
Hoisting Speed (f/min.)
31.50
24.80 12.40 8.30 6.20
Headroom (in 10', 15' and 20' lifts.
The above specifications were current at the time this manual was published, but because of our policy...
User Manual - Page 9
... from the hoist. 2. Refer to socket, check that is properly installed and grounded in compliance with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in a risk of least resistance for electric current to disengage notch.
Repair or replace damaged or worn cord immediately. NOTE: When connecting plug to...
User Manual - Page 12
...Replace a hook immediately if any of excessive hoist loading. If such deformation is discovered, inspect hoist, chain and all supporting members very carefully for additional indications of the following problems... factory replacement chain may need to a manual trolley,...° (see Figure 15). Use of the hoist...not attempt repair of each hoist must be replaced.
Excessive wear...
User Manual - Page 13
...Clutch Adjustment
The load limitation of the safety clutch has been set to within 1.3 to 1.8 times the rated load, then ...is turning, the safety clutch must be able to ground or new support. Rotate the nut (H) clockwise to lift the load. If it can... 6 with the adjusting circle nut (L). Unload the hoist, and re-install the gear side cover.
13
Figure 14 Now change the load to within...
User Manual - Page 14
....
The following the instructions in this manual. Cut a link from the link leaving an opening...17). 5. Install chain container following procedures describe replacing the load chain for twist before placing hoist in routine service. Making a C-Link
Replacing load chain... 8. Figure 15
Single Fall Chain Hoist
1. Be sure vertical link welds face away from the
old chain, and install them on ...
User Manual - Page 17
... passes through all ANSI and JET inspection and maintenance instructions. Perform all of excessive load brake wear. Check for evidence of the Schedule A items.
2. Check for the hoist system being serviced. Check that load chain is the customer's responsibility to understand and follow the ANSI Inspection and Maintenance instructions. All replacement chain must be maintained...
User Manual - Page 19
...the chart below.
Before suspecting or replacing the brake friction pad, make sure...1C 1/2SS-3C
1SS-1C 1SS-3C
2SS-1C 2SS-3C
3SS-1C 3SS-3C
5SS-1C 5SS-3C
A A A A A A A A A A C C C C C C C C B B B B B B B B B B D D D D D D D D BBBBDDDDDDEEEE - - - If the friction pad is under 0.55"
Figure 23
Do not attempt to the instructions on pages 13 and 16.
BBDDDDEE BDDDEE
A = Chain Container part...
User Manual - Page 20
... fuse/re-set circuit breaker. Replace transformer.
Have clutch replaced by a qualified service technician.
Excessive load or too frequent use. Adjust brake clearance (see page 10).
Overload limit clutch friction torque too low.
Up/down switch malfunctioning. Repair or replace switch.
Open the hoist, disassemble the brake and clean the lining. Replace brake springs. Hoist...
User Manual - Page 21
... the Model Number and Serial Number of your machine available when you call 1800-274-6848 Monday through Friday (see our website for 3 Phase 1
21 Replacement Parts
Replacement parts are listed on the following pages. Description
Size
Qty
106........... 1/2SS-3C-106 ..........Cord Holder Assembly 1 123........... 1/2SS-3C-123UG.....Male Plug 4P 1 124........... 1/2SS-1C-124...
User Manual - Page 35
...1C-004 Rotor Assembly for 1 Phase 1 1SS-3C-004 Rotor Assembly for 3 Phase, Single Speed 1 5 1SS-3C-005 Ball Bearing 180206kz1 1 6 1SS-1C...-006 Motor Case Assembly for 1 Phase 1 1SS-3C-006 Motor Case Assembly for 3 Phase, Single Speed 1 7 1SS-1C...15 3SS-3C-015 Stay Bolt for Top Hook Assembly 2 16 5SS-3C-016 Motor Side Plate 1 17 5SS...5SS...-1C-03503 ............Clutch Support 1...1C...
JET Tools 5SS-1C-15 Reviews
Do you have an experience with the JET Tools 5SS-1C-15 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!