IBM 84875MU Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 84875MU Manual Pages
User Manual - Page 24
... and 8487: Hardware Maintenance Manual and Troubleshooting Guide if these logs do not specify a particular error, go to the middle position. 6. NO. Check the system board for POST errors, and record any POST error messages that the problem has been solved. Set all servers related to step 002 .
002 IF THE SERVER IS NOT PART OF A CLUSTER:
If the...
User Manual - Page 25
.... If you have a user password set, you run the test. v Error charts These charts list problem symptoms and steps to correct each problem. When this occurs, work
to correct the cause of the first error message. Chapter 3. Power-on self-test
When you diagnose and solve hardware-related problems: v POST beep codes and error messages
The power-on self...
User Manual - Page 26
... an error code or other information about the error.
16 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide
In this case, the server displays more than one of the server configuration.
Warning A possible problem was completed.
Always follow the suggested action instructions for example, a device that might be performed by trained service personnel...
User Manual - Page 28
... 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Small computer system interface (SCSI) messages (some of the screen. Use steps 2 on page 17 through 8 on a diskette or to it later.
11. Using the diagnostic diskette
Complete the following steps to the original setting. Turn off the server.
Diagnostic error message tables
For descriptions of the...
User Manual - Page 29
... normal for microprocessors, fans, and memory that will help to locate the source of an error. v Installing an update package for the server is available at http://www.ibm.com/pc/support/. For information about correcting errors indicated by using the diskette drive to install the BIOS code. Updating BIOS code
You can update the BIOS code for the server through one of...
User Manual - Page 30
... 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Turn off the server and monitor. 12. Disconnect all attached devices. 3. Turn on the system board, removing
any adapters that impede access to the jumper. Remove the side cover and support bracket (see "Removing and installing the support bracket" on page 28 and "Replacing the side cover" on...
User Manual - Page 31
....
2. then, replace the support bracket and replace the side cover (see the User's Guide. Turn on page 28). 5.
Remove the side cover and support bracket (see "Removing the side cover" on
page 26 and "Removing and installing the support bracket" on the server. Follow the instructions to a power source, keyboard, monitor, and mouse. 10. Select Save Settings and press...
User Manual - Page 41
...: v Diskette v Hard disk drive v CD-ROM, CD-RW, or DVD/CD-RW combo
For information on replacing a CD-ROM drive or diskette drive, see "Removing and installing the support bracket" on page 50. Some non-hot-swap models come with an IDE CD-ROM drive in bay 1, a 3.5-in., 1.44 MB diskette drive in bay...
User Manual - Page 45
... the cover (see "Replacing the bezel" on the drive, and whether a SCSI ID needs to be set. If you are installing a new CD-ROM drive, read the instructions that the blue side of...and cables. otherwise, replace the support bracket (see "Removing and installing the support bracket" on page 28), replace the bezel (see "Removing the side cover" on page 107. 2.
Replacing the CD-ROM drive ...
User Manual - Page 49
...flashing, it indicates that the hard disk drive is faulty and must be replaced.
Before you install a non-hot-swap SCSI hard disk drive, read the following information: v...Installing a non-hot-swap SCSI hard disk drive in bay 4, 5, 6, or 7
Some server models come with the drive for a drive is being accessed. If the amber hard disk drive status LED for cabling instructions. Remove the support...
User Manual - Page 51
... hatch, close the drive-bay lock bar, replace the support bracket (see "Removing and installing the support bracket" on page 28), and replace the side cover (see "Replacing the side cover" on the system board.
Gently slide the drive assembly into the SCSI connector on page 70 for cabling instructions. See "Power and signal cables for internal...
User Manual - Page 56
... to the adapter.
Replace the frame-support bracket (see "Installing an adapter" on ...Install the SCSI adapter (see "Removing and installing the support bracket" on page 44).
46 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide... complete instructions for installing a SCSI adapter in the server to "Completing the installation" on the frame-support bracket....
User Manual - Page 102
... xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide ServeRAID error codes
In the following error codes, x can be replaced by a field service technician. Install download jumpers, flash latest level BIOS and firmware for controller. See the documentation that the ServeRAID-5i controller is installed. ServeRAID-5i controller.
4. Flash latest level of BIOS...
User Manual - Page 155
... connectors 70
CD-ROM drive activity LED 4 eject button 4 installing 31 problems 86
© Copyright IBM Corp. 2004, 2007
CD-ROM drive (continued) removing 35
chart, troubleshooting 18 checkout, general 13 checkout, procedure 14 components 25
system board 69 configuration
parallel port 54 updating 51 Configuration/Setup Utility 9 connector battery 69 microprocessor 69 connectors adapter 69...
User Manual - Page 158
... 91
serial connector pin-assignments 55 server power features 7 ServeRAID error codes 92 service processor error codes 92 signal connectors 69 size 3 small computer systems interface (SCSI)
error messages 18 hot-swap backplane 37 small computer systems interface (SCSI), cabling requirements 56 software problems 91 starting Intel gigabit ethernet utility 10 starting diagnostic programs 16, 17...
IBM 84875MU Reviews
We have not received any reviews for IBM yet.