Honeywell HCM-631N - Quietcare 3 Gallon Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell HCM-631N manuals!
Problems with Honeywell HCM-631N?
Ask a Question
Free Honeywell HCM-631N manuals!
Problems with Honeywell HCM-631N?
Ask a Question
Most Recent Honeywell HCM-631N Questions
How And Where Do I Install The Filter?
(Posted by roxannpatrick 13 years ago)
Popular Honeywell HCM-631N Manual Pages
User Guide - Page 1
... and gasket H Owner's manual I
J3
Tools needed to local codes for proper draining practices for hot water.
GETTING STARTED
TrueSTEAM™
TM
PROFESSIONAL INSTALLATION GUIDE
INCLUDED IN THIS HUMIDIFIER BOX
MOUNTING
PLUMBING
WIRING
OPERATION AND SERVICE
G
F
H
E I Service label J3 Humidity control* J4 VisionPRO IAQ control*
* Control based on model ordered. drill bit Standard...
User Guide - Page 3
... Tank 49 STEP FOUR: Replace the Water Level Sensor 49 Changing the Water Filter 50
Water Level Sensor Troubleshooting Steps...........51 Test Setup 51 Test Pins 51 Testing for Shorts 51 Good Water Sensor 51 Bad Water Sensor 51 STEP FIVE: Reinstall the Tank 52
Troubleshooting 53
A: Specifications 58
B: Parts List 59
PLUMBING
WIRING
OPERATION AND SERVICE
APPENDICES
?
User Guide - Page 6
... to address the issue of water quality and hardness, homes with extreme hard water problems should consider using softened water, use of a whole house water softener will accomplish ...all local plumbing codes before beginning installation. In applications with a water softener, it is critical for the TrueSTEAM to draw its available filtration options help protect the humidifier from the cold...
User Guide - Page 8
...STARTED
In the event that a service technician needs to call in to the TrueSTEAM support techline, the following information is...Install Information
Model Number of TrueSTEAM Unit
Date Code (xxxx)
Water Quality Test
1
2
3
(circle one)
Water Pressure Test (psi)
Flush Cycle Setting
Duct Static Pressure Test (in.wc.) (Maximum static pressure is typically required for the Honeywell tech support...
User Guide - Page 10
At startup, it with dry air. TrueSTEAM will help you determine the cleaning interval and filter requirements for your TrueSTEAM. If installing a ventilator, use a solution that retains moisture. If the remote hose is provided with the homeowners and answer any humidifier. This can save up to a week of home, furnishings in the home, and...
User Guide - Page 11
... and all local regulations.
GETTING STARTED
Important Installation Requirements
Failure to comply with a Honeywell
duct board adapter kit. See "Appendix B: Parts List" on page 59. • If...installation, and service callbacks. The remote mount nozzle attachment is lower than 34°F (1.1°C) or higher
than 104°F (40°C). • Mounting area must be strong enough to support...
User Guide - Page 12
...
This manual covers duct mounting of installation, but it requires that a suitable mounting location can be found on the supply duct:
The TrueSTEAM can not be mounted up to 20 feet away from TrueSTEAM to use : Duct Mounting Remote Mounting
10
TrueSTEAM Humidification System 69-2285-01 For Remote Mounting Instructions, see "Appendix B: Parts...
User Guide - Page 15
... TWO: Tap into a Water Line
Water Supply Line
T-fitting
Manual Shutoff Valve
Saddle Valve
M29605
• Consult local codes for proper plumbing. • Use the saddle valve provided or a T-fitting and
manual shutoff valve to tap into the water filter
or reverse osmosis kit.
Install the provided backflow preventer, as needed based on the bottom...
User Guide - Page 26
... line to and follow local codes for complete installation instructions.
6
Cold Water Supply
2
Manual Shutoff Valve
1/4" White Tubing
White Tubing
1
3
2
4
5 Yellow Tubing
Red Tubing Drainflow Control
3
Backflow Preventer
4
SCtloeraangeWTaatenrk
1. Refer to additional drain requirements in the TrueSTEAM installation guide when coupling the RO Filter
drain with the RO Filtration...
User Guide - Page 36
Refer to the installation manual provided with the control for control options 1 through 14 to wire the TrueSTEAM. All Honeywell Prestige, VisionPRO IAQ, VisionPRO, and ...from G. Follow the diagram for additional instructions if needed. All Honeywell Prestige, VisionPRO IAQ, VisionPRO, and Focus Pro thermostats do this .
2 For the TrueIAQ Installer Setup, set ISU #25 to HVAC terminals, ...
User Guide - Page 46
IN SETUP UNDER THE INSTALL/SERVICE MENU: A.
A 24VAC ISOLATION RELAY MUST BE USED BETWEEN THE FURNACE AND THE HUMIDIFIER TO ISOLATE THE TWO TRANSFORMERS. THIS WILL ALLOW THE HUMIDIFIER TO CONTINUE TO RUN THE FAN AFTER THE HUMIDIFICATION CALL IS SATISFIED. MAKE SURE AIRFLOW SATISFIES ANY MINIMUM REQUIREMENT FOR YOUR TRUESTEAM HUMIDIFIER.
M33044
WIRING
44
TrueSTEAM ...
User Guide - Page 48
... throughout the humidifying season. The manual cleaning is ... SERVICE
M29628
CAUTION: Burn and Scalding Hazard.
The water exiting the TrueSTEAM may be as hot as normal while this light is on , manual
cleaning... enter the tank to
normal operation. Manual Cleaning Cycle
Honeywell recommends that TrueSTEAM be manually cleaned and the water filter be completely drained.
This lowers the ...
User Guide - Page 52
... of the filter.
OPERATION AND SERVICE
50
TrueSTEAM Humidification System 69-2285-01 Apply a modest pull to install the new filter correctly. Changing the Water Filter
Replace the polyphosphate water filter at the saddle valve or T-fitting
1
and manual shutoff valve.
2 3
4 5
Press down on the filter must point to TrueSTEAM in place with clamps or ties to support weight. M29634...
User Guide - Page 53
Always unplug the humidifier before testing.
Testing for Shorts
• Use an OHM METER and set it to the highest setting.
• Place the OHM METER PROBES on pins. Test Setup
• Remove ...AND SERVICE
Water Level Sensor Troubleshooting Steps
WARNING: Electrocution Hazard. Good Water Sensor
The water sensor is bad if any pins show an infinite reading. The tank must be replaced. ...
User Guide - Page 58
... 46. Ensure DIP switches are set correctly. (DIP 4 down, DIP 5 up
if TrueSTEAM R and C aren't wired.) 3. Reconnect cover and plug in manual. 4. Ensure DIP switches are set correctly. (DIP 3 up. ... fault persists, replace the wireless adapter.
1. Ensure tank water is 120 Vac at heating element terminals. 6. See "Manual Cleaning Cycle" on air proving device is on. of Service LED Blinks
13...
Honeywell HCM-631N Reviews
We have not received any reviews for Honeywell yet.