Hikvision DS-K1107M Support and Manuals
Get Help and Manuals for this Hikvision item
This item is in your list!
View All Support Options Below
Free Hikvision DS-K1107M manuals!
Problems with Hikvision DS-K1107M?
Ask a Question
Free Hikvision DS-K1107M manuals!
Problems with Hikvision DS-K1107M?
Ask a Question
Hikvision DS-K1107M Videos
Popular Hikvision DS-K1107M Manual Pages
User Manual - Page 2
..., pictures, graphs are for using and managing the product. The information contained in the Manual is applicable to DS-K1106 series card reader The Manual includes instructions for description and explanation only. ALL RIGHTS RESERVED. About this user manual under the guidance of Hikvision in the company website (http://overseas.hikvision.com/en/). Any and all other reasons.
User Manual - Page 3
...SUPPORT IF REQUIRED. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
0100001060229
ii PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION...OTHER INTERNET SECURITY RISKS; IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE...
User Manual - Page 4
... use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal.
2 Chapter 1 Preventive and Cautionary Tips
To guarantee the card reader works properly, please read and obey the notes below. If...
User Manual - Page 5
... physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment.
3 As to protect card reader from malicious damage. Chapter 2 Introduction
2.1 Over View
Figure 2-1 DS-K1107 Series Card Reader DS-K1107 series card reader is a kind of high-performance product, with access controller via either RS-485 protocol (AES encrypted) or Wiegand protocol...
User Manual - Page 6
2.2 Indicator and Component
Figure 2-2 2.2 Indicator and Component
Chapter 3 Installation
3.1 Introduction for DIP Switch
The DIP switch module is 1 ~ 8.
4 of DIP switch from left to right is shown below. The No.
User Manual - Page 8
... LED Control (available for Wiegand Protocol)
3.3 Wiring Cables
Purpose: Wire the cables between controller and card reader, thus to 3.1 Introduction for DIP Switch. 3. Wire the cable between them.
Table 3-3 Description of No. 1 ~ 4 for RS-485 communication mode: 1. Set the DIP switch of 10 cables is shown below. Steps for RS-485 address and...
User Manual - Page 9
... No. 7 for DIP Switch. 3.
For details, please refer to 3.1 Introduction for reading card mode and Wiegand protocol. Set the DIP switch of No. 6 as shown below . Wiring the cable between controller and card reader as 1. 2. Controller
Yellow Blue Black Red Black
Card Reader
Card Reader Figure 3-3 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode: 1. shown...
User Manual - Page 10
For details, refer to 3.1 Introduction for Wiegand Communication Mode
3.4 Installing Card Reader
Before you start: Set the DIP switch. Green
Black Red Green White Purple Orange Brown
Brown
Controller
Card Reader
Card Reader Figure 3-4 Wiring for DIP Switch.
8
User Manual - Page 11
... A to make sure it will turn red and blink for DS-K1101/ 02/ 03/ 04 series card reader Steps: 1. Check whether the plate is fixed.
Fix the plate on the wall or other places by using two screws (PA4×25-SUS). Make sure the card reader is powered on the plate are upwards. 2. Installation for 3
9
User Manual - Page 12
... authentication: prompt for tamper-proof alarm. Prompt for pressing the fingerprint after swiping the card. The card reader is completed. times. You can refer to indicate different statuses. Prompt for detailed information. When using the card reader, it will send out a beep sound indicating the starting up process is unencrypted.
10 input by pressing keys...
User Manual - Page 13
... Red and blink for pressing the fingerprint after swiping the card. Card reader is offline.
11 The operation of configuring the fingerprint. For RS-485 protocol: Registering failed or card reader is working normally. The operation of pressing keys or swiping card is power on.
For Card + Fingerprint authentication: prompt for 3 times Red and blinking
Description
The...
Data Sheet - Page 1
...the ISO 14443-A standard and reads Mifare ID cards Available Models: DS-K1107M/MK: Mifare card reader w/keypad
DS-K1107M/MK
Card Reader
LED Indicator Displays Reader Status Tamper-Resistant Alarm Supports Mifare Cards Keypad (Optional) RS-485 and Wiegand (W26/W34) Protocols Hikvision DS-K1107M/MF card readers support RS-485 and Wiegand (W26/W34...
Data Sheet - Page 2
Specifications
Processor Reading Range
Card Type ID Settings Communication Protocols Audio Alert
Keypad LED Indicator Working Temperature Working Humidity
Dimensions Tamper Alarm Protection Level Certifications Power Supply Power Consumption Installing Method
DS-K1107M
DS-K1107MK
32-bit ≤1.97" (≤50 mm)
Mifare cards
via DIP switch
RS-485/Wiegand (set via DIP switch)
Beeper
No ...
Hikvision DS-K1107M Reviews
Do you have an experience with the Hikvision DS-K1107M that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hikvision yet.
Earn 750 points for your review!