Harbor Freight Tools 95504 - 4 in. Air Angle Grinder Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 95504 manuals!
Problems with Harbor Freight Tools 95504?
Ask a Question
Free Harbor Freight Tools 95504 manuals!
Problems with Harbor Freight Tools 95504?
Ask a Question
Popular Harbor Freight Tools 95504 Manual Pages
User Manual - Page 1
Due to do so can result in any artwork contained herein may differ slightly from the product described herein. Tools required for assembly and service may not be included. Revised Manual 11h 4" AIR ANGLE GRINDER
Model 95504
ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this...
User Manual - Page 2
... This Manual
You will do the job better and more safely at the rate for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and... personal injury and damage to exceed the tool capacity. Children must be followed to rain. Specifications
ITEM Overall Dimensions Handle Dimensions
DESCRIPTION 7-1/2"L x 5"W x 3-3/4"H 1" Dia. Always lock up...
User Manual - Page 3
...to do not use . Keep proper footing and balance at all times. Follow instructions for damaged parts. Disconnect tool from air compressor hose when not in use and before plugging ... approved impact safety goggles. Maintain tools with these materials extra care should be properly repaired or replaced by an authorized technician. Use eye and ear protection. Do not overreach. When ...
User Manual - Page 4
...servicing, use oxygen, carbon dioxide, combustible gases or any doubt, do not operate the tool.
20. Do not operate tool if under the influence of this instruction manual...reproductive harm). (California Health & Safety Code § 25249.5 et seq.). There...replacement parts. Warning: The warnings, cautions, and instructions discussed in this tool (if powered by the operator. Replacement parts...
User Manual - Page 5
...Always use Couplings (not supplied) as listed on this manual. Always disconnect from abrasion.
6. Two-handed operation is not supplied. WARNING: Never install a carbide tipped or steel circular saw chain cutters, or... accessories running over rated speed can fly apart and cause injury.
3. If any parts are included.
Use a cloth or glove to the Air Inlet. Make sure accessories...
User Manual - Page 6
... tools.
4.
Always wear ANSI approved impact safety goggles when setting up and using the Stop Spanner and Disc Spanner. Set the Air Compressor's pressure regulator to the air fitting if ...of the Air Hose to prevent the Shaft from spinning. Attaching/Changing the Wheel Accessory
1.
Replace the Disc Nut and tighten using this tool.
2. Tighten with the air supply as shown...
User Manual - Page 7
... OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Depress the Lever [31] with your right hand to turn the tool on page 8. Do not force the wheel or apply too much pressure.
8. Maintenance and Troubleshooting
Caution: Always disconnect the...
User Manual - Page 8
Assembly Drawing
(not included)
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
SKU 95504
Page 8
REV 07i, 09l
User Manual - Page 9
Parts List
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
DESCRIPTION Disc Nut Grinding Wheel (not included) Screw Spring Washer Disc Cover Gear Shaft ...
User Manual - Page 10
... vary from state to the original purchaser that this warranty, the product or part must accompany the merchandise. To take advantage of this product is no event ... misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to us with a replacement. We shall in materials and workmanship ...
Harbor Freight Tools 95504 Reviews
We have not received any reviews for Harbor Freight Tools yet.