D-Link DP-100 Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DP-100 manuals!
Problems with D-Link DP-100?
Ask a Question
Free D-Link DP-100 manuals!
Problems with D-Link DP-100?
Ask a Question
Popular D-Link DP-100 Manual Pages
Product Manual - Page 1
Model DP-100 Multiprotocol Ethernet
Print Server Hardware User's Guide
Rev. 01 (May, 1997)
6DP100H.001 Printed In Taiwan
RECYCLABLE
Product Manual - Page 5
...repair the defective product or part, (2) deliver to Customer an equivalent product or part to replace the defective item. To find out if a service charge is levied or not, and the charged amount, read the RMA that are replaced...D-Link or its Authorized Reseller:
Product Type Network adapters Print servers (10Mbps) Print servers (100Mbps) Unmanaged and managed hubs (10Mbps) Unmanaged and...
Product Manual - Page 11
... THIS GUIDE
This manual describes the DP-100 Ethernet Multiprotocol Print Server, including a description of the DP-100 to allow it to be used with your network, consult the Print Server Administration User's Guide included with your DP-100.
For information about software configuration of the print server's features, as well as the print server installation procedures and troubleshooting self...
Product Manual - Page 13
... a print server can. DP-100 Multiprotocol Ethernet Print Server User's Guide
1
1 INTRODUCTION
The DP-100 Print Server is a compact print server which connects to your workstations or file servers to its connected printers, delivering print jobs to locate printer services.
Figure 1 -1 DP-100 Print Server
DP-100 Print Server Features
DP-100 print servers improve network printing services in...
Product Manual - Page 14
...printers can transmit to its connected printers. ♦ The DP-100 picks up the workload of managing print file traffic to high-speed laser printers much faster than a PC's parallel printer port. On peer-to-peer networks, workstations can print directly to the DP-100 without increasing the load of another workstation or server.
♦ The DP-100's parallel printer... services to users.
Product Manual - Page 15
...DP-100 Multiprotocol Ethernet Print Server User's Guide
Windows-based setup and administration software, PS Admin, is labeled COM. The DP-100 also supports configuration and management via the telnet protocol for information about configuring the print server's ports.)
Figure 1 -2 Port Connectors
Introduction
3 Two identical parallel ports are located on its rear panel.
These printer...
Product Manual - Page 17
..., COM
◊ These LED indicators light to indicate any hardware failures. DP-100 Multiprotocol Ethernet Print Server User's Guide
◊ The indicator blinks off briefly to indicate that the DP-100 is transmitting to the network.
♦ Link/Rx
◊ Steady or flashing green confirms that the DP-100 has a good connection to the Ethernet network.
◊ The indicator...
Product Manual - Page 18
...
This chapter explains how to install your DP-100 print server and connect it to this Hardware User's Guide, be certain that you have:
♦ One DP-100 print server ♦ One DC power adapter suitable for your country's electric power ♦ Two PS Admin software diskettes ♦ One Print Server Administration User's Guide ♦ Fasteners for optional wall-mounting
If any item...
Product Manual - Page 19
... Print Server User's Guide
Installing the DP-100
WARNING: Configuration problems may result if the DP100 is operating normally.
4. port connections are connecting fewer than three printers, then keep in connecting to the PC through the same port (serial or parallel) as it has no external power switch. Plug the DC power adapter's DC output plug into an electric service...
Product Manual - Page 20
.... Power On Self-Test
When the DP-100 is signaled by a series of three cycles of sequential flashing of the three LEDs, followed by the state of the self-test is a problem with all five of the LED's should show steady green for correction of any component error, then following the LED tests the...
Product Manual - Page 21
...to a wall or partition adjacent to reload firmware
Testing Your DP-100
The PS Admin software includes a Print Test function for confirmation of printer cable connections and functions.
That operational test can be completed after you have installed the PS Admin software, and have configured your printers. DP-100 Multiprotocol Ethernet Print Server User's Guide
off off on/steady on/steady on...
Product Manual - Page 23
DP-100 Multiprotocol Ethernet Print Server User's Guide
A
3 PRODUCT SPECIFICATIONS
Printer Connection
Standards: IEEE 1284 bi-directional parallel interface, RS-232 Ports: Bi-directional 25-pin parallel ports × 2, 9-pin DTE serial port × 1 Parallel Port Bi-directional Communication: Hewlett-Packard PJL (Printer Job Language) supported
Network Connection
Network Standards: IEEE 802.3 ...
Product Manual - Page 25
DP-100 Multiprotocol Ethernet Print Server User's Guide
Safety: UL (UL 1950), CSA (CSA950), TUV/GS (EN60950)
Product Specifications
13
Product Manual - Page 26
... Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Printer Printer Printer
14
Port Pinouts Parallel Ports
The following table lists the pinouts of the DP-100 parallel and serial printer ports. B
4 PORT PINOUTS
This appendix shows the pinouts of the print server's 25-pin parallel port connector (identical to the connector used on most...
Product Manual - Page 27
...) Transmitted Data (DTEÆDCE) Data Terminal Ready (DTEÆDCE) Signal Ground Data Set Ready (DCEÆDTE) Request to Send (DTEÆDCE) Clear to a DCE (Data Communications Equipment) serial port on your printer. DP-100 Multiprotocol Ethernet Print Server User's Guide
25-pin
13 14 15 16 17 18-25
Centronics
13 14 32 31...
D-Link DP-100 Reviews
We have not received any reviews for D-Link yet.