Cisco 4215 - Intrusion Detection Sys Sensor Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 4215 Manual Pages
Configuration Guide - Page 40
... created the service account for IPS 5.0
3-2
78-16527-01 Or, if you have to reimage your sensor (see Creating the Service Account, page 4-13. Cisco Intrusion Prevention System Sensor CLI Configuration Guide for support purposes, you are based on month, day, year, and time.
For more information, see Chapter 17, "Upgrading, Downgrading, and Installing System Images"), unless there...
Configuration Guide - Page 41
...= 0-255.
78-16527-01
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for help. Specify the IP interface. Default settings are not acceptable. Type the setup command.
Press Enter to continue. Type yes to show one line at any point you change the password, the sensor# prompt appears. The default is in the form of IP Address/Netmask,Gateway: X.X.X.X/nn,Y.Y.Y.Y, where...
Configuration Guide - Page 45
...to obtain the most recent service pack and signature update. Current configuration last modified Thu Aug 12 16:55:33 2004 service analysis-engine global-parameters ip-logging max-open-iplog-files 30 exit exit virtual-sensor vs0 description default virtual sensor physical-interface GigabitEthernet0/1 exit exit service authentication exit service host network-settings host-ip 10.89.146.110/24...
Configuration Guide - Page 222
...|deny-conne ction-inline|deny-packet-inline|log-attacker-packets|log-pair-packets|log-victim -packets|request-block-connection|request-block-host|request-snmp-trap|reset-tcp
12-14
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for IPS 5.0
78-16527-01
Configuration Guide - Page 247
... support for the serial connection. exit time-zone-settings --MORE--
Step 3 View configuration information:
Note You can use the more current-config Version 5.0(0.26) !
Use the no display-serial command to reset the output to the following platforms: • IDSM-2 • NM-CIDS • IDS-4215
78-16527-01
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for IPS...
Configuration Guide - Page 261
... doing a hardware reset. For the procedure for setting or changing the recovery parameters. You can change the parameter or keep the existing setting by pressing Enter. It is applicable when the card is in the Unresponsive state.
78-16527-01
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for any reason:
asa(config)# access-list IPS permit ip any any...
Configuration Guide - Page 314
...chassis. Note The default port used as noted by pinging it from the local Ethernet port:
rommon> ping server_ip_address rommon> ping server
17-12
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for the local port on the back of IDS-4215. Installing System Images
Chapter 17 Upgrading, Downgrading, and Installing System Images
Step 4
Image Download Memory Sizing Available...
Configuration Guide - Page 315
... this message is relative to the UNIX TFTP server's default tftpboot directory. Chapter 17 Upgrading, Downgrading, and Installing System Images
Installing System Images
Step 10 Specify the path and filename on Cisco.com, see Obtaining Cisco IPS Software, page 18-1.
The console display resembles the following:
CISCO SYSTEMS IDS-4215 Embedded BIOS Version 5.1.3 05/12/03 10:18:14.84 Compiled...
Configuration Guide - Page 321
.... Type the setup command to change the password, the sensor# prompt appears. Note A blue screen is , not be a dictionary word.
Install the most recent service pack and signature update. Chapter 17 Upgrading, Downgrading, and Installing System Images
Installing System Images
Step 4 Type k if you are installing from a keyboard, or type s if you are both cisco.
You only...
Configuration Guide - Page 324
... version cannot launch IPS 5.0(1). Therefore, you can boot the IDS 4.1 image with the setup command. The 1.0.17-1 bootloader is complete, NM-CIDS reboots. To avoid this situation, download the bootloader file to use the upgrade command, see Upgrading the Sensor, page 17-2.
When the installation is backwards compatible with the upgrade file, in to default settings. The bootloader that...
Configuration Guide - Page 431
... Configuration Guide for help. Make sure the management port is not connected to an active network connection, the management interface will not come up .
At any prompt. Default settings are in the list with the status line Media Type = TX.
System Configuration Dialog --- If the Link Status is the interface in square brackets '[]'. sensor# setup --- Appendix C Troubleshooting...
Configuration Guide - Page 432
...the Access List, page 4-5. Add a permit entry for the workstation's network address, save the configuration, and try to the CLI.
If it :
sensor# configure terminal sensor(config)# service host sensor(config-hos)# network-settings sensor(config-hos-net)# access-list 171.69.70.0/24
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for help. At any prompt. Make sure the network...
Configuration Guide - Page 444
... C-19. Make sure the you have the correct IP address and username and password for the managed devices and the correct interface and direction configured.
Verify the IP address for the managed devices:
sensor# configure terminal sensor (config)# service network-access sensor(config-net)# show settings
general
log-all-block-events-and-errors: true enable-nvram-write: false enable-acl...
Configuration Guide - Page 459
... key:
sensor# configure terminal sensor(config)# service ssh sensor(config-ssh)# rsa1-keys sensor_ip_address
Upgrade the sensor: sensor(config)# upgrade scp://service@sensor_ip_address/upgrade/ips_package_file_name
Enter password: *****
78-16527-01
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for IPS 5.0
C-33
Make sure they match the same passwords used for manual update...
Configuration Guide - Page 463
...# setup
---
Current Configuration:
service host network-settings host-ip 10.89.130.108/23,10.89.130.1 host-name sensor telnet-option enabled access-list 0.0.0.0/0 ftp-timeout 300 no login-banner-text exit time-zone-settings offset 0 standard-time-zone-name UTC exit summertime-option disabled ntp-option disabled exit
78-16527-01
Cisco Intrusion Prevention System Sensor CLI Configuration Guide...
Cisco 4215 Reviews
We have not received any reviews for Cisco yet.