Chamberlain PD222 Support and Manuals
Get Help and Manuals for this Chamberlain item
View All Support Options Below
Free Chamberlain PD222 manuals!
Problems with Chamberlain PD222?
Ask a Question
Free Chamberlain PD222 manuals!
Problems with Chamberlain PD222?
Ask a Question
Popular Chamberlain PD222 Manual Pages
1/2 HPS Chain Drive Garage Door Opener Manual - Page 1
... Drive Garage Door Opener
Models HD220, HD220C, PD220, PD222, and LW260C
FOR RESIDENTIAL USE ONLY
INSTALL ON 7 FOOT SECTIONAL DOORS ONLY
Register your new garage door opener at www.prodregister.com/chamberlain or scan the QR code with your garage door opener. ■ This garage door opener is compatible with a
7 foot sectional door. CONTENTS
Preparation 1-4 Assembly 5-9 Installation 10...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 2
...damage to your door binds, sticks, or is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. l ONLY operate garage door opener at 120 ...Signal Word Review
This garage door opener has been designed and tested to offer safe service provided it is out of balance, call a trained door systems technician if garage door binds, ...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 3
... the safety reversing sensors.
n EXTENSION BRACKETS (MODEL 041A5821-1) OR WOOD BLOCKS Depending upon garage construction, extension brackets or wood blocks may be used to install the safety reversing sensor. n SUPPORT BRACKET AND FASTENING HARDWARE Must be needed to position the garage door opener during installation and for a garage with NO access door. Also used if you have...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 4
...the installation and adjustment is packaged in this manual are not included in one carton which contains the motor unit and all parts illustrated below. Depending on the garage door opener model purchased. Key Description
A Header bracket
B Pulley (In hardware bag)
C Door bracket
D Curved door arm
E Straight door arm (Packaged inside the front rail section)
J Garage door opener (motor...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 6
...the motor unit, as shown. 6.
Use these grooves to do not run the garage door opener until it stops. To avoid installation difficulties, do so. Slide the tapered ends into place.
3. If they became ... onto the rail until instructed to align the rail sections. TIP: Ensure the rail sections are 4 plastic wear pads inside the front rail and set aside for Installation Step 5 and 9.
1/2 HPS Chain Drive Garage Door Opener Manual - Page 11
... parts of the garage door. Mount the emergency release within sight of the door. 10. NEVER connect garage door opener to power source until instructed to avoid entanglement. 5. Upon completion of garage door. 12. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener
to do so.
8. NEVER wear watches, rings or loose clothing while installing or servicing...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 14
...setting the distance between the rail and the door. Clevis Pin 5/16"x1-1/2"
HARDWARE
Ring Fastener
Clevis Pin 5/16"x1-1/2"
Ring Fastener
STEP 4 Position the garage door opener
To prevent damage to the header bracket
1. Connected
Disconnected
13 Secure with the header bracket. Slide the outer trolley toward the garage door opener. The trolley can remain disconnected until instructed...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 15
...
HARDWARE
4
5 Hex Bolt
6
1/4"-20x3/4"
Lag Screw #14-10x1-1/2"
Lock Nut 1/4"-20
(not provided)
Lock Nut 1/4"-20
Hex Bolt 1/4"-20x3/4"
14 For ALL installations the garage door opener MUST be connected to the support bracket. 3. The instructions illustrate one of the garage.
Cut both pieces of the garage door opener to structural supports. Remove the 2x4 and manually close the...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 20
... end of the garage door.
1. Clean surface and attach the manual release/safety reverse test label in the tab with tacks or staples. 2. Do not pierce the wire with the staple (not applicable for gang box or pre-wired installations).
Strip 7/16 inch (11 mm) of insulation from the door control to the garage door opener
HARDWARE
Insulated...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 21
... Snap into the sleep mode until activated. NOTE: For energy efficiency the garage door opener will not support the sensor bracket a wall installation is recommended. Insert the bolt through the hole in the down until the garage door opener has completed 5 cycles upon power up.
The garage door opener will not go into place so that the sensor bracket is flush...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 23
... white terminal on the garage door opener. Strip 7/16 inch (11 mm) of wires. To insert or remove the wires from the
terminal, push in the tab with the staples.
3
2. Attach the wire to page 23.
2 Staple
HARDWARE
Insulated Staple (Not Shown)
OPTION A INSTALLATION WITHOUT PRE-WIRING
1. Separate the wires. Installation
STEP 14 Wire the...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 32
... to the instructions provided with your choice on the garage door opener. When the door is closed and the garage door opener is fully closed and the garage door opener is interrupted while opening cycle. The safety reversing sensors do not affect the opening the door will stop. Remote Control:
Press and hold the button on the make, model, and year of your garage door opener.
1/2 HPS Chain Drive Garage Door Opener Manual - Page 34
... system. The garage door opener does not require additional
lubrication.
l DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.
The 3V CR2032 lithium battery should produce power for compliance could void the user'sauthorityto operate
the equipment.
Dispose of old batteries properly.
3
1 2
3 4
2
NOTICE: This device complies with Part 15 of fire...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 35
... capabilities.
NOTE: For troubleshooting questions, please visit www.chamberlain.com. disconnected or cut . Inspect safety sensor wire at the logic board. The wires for the door control are not installed, connected, or wires may be cut wire.
1
2
The garage door opener will not close and the light Safety sensors are steady and not flickering.
Manually open and close and...
1/2 HPS Chain Drive Garage Door Opener Manual - Page 36
... TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES.
This garage door opener WILL NOT work until the safety reversing sensors are calling for a period of one year from the date of purchase and that the motor is free from the date of -purchase receipt with the instructions regarding installation, operation, maintenance and testing. Address repair parts orders to...
Chamberlain PD222 Reviews
We have not received any reviews for Chamberlain yet.