Campbell Scientific SC532A Support and Manuals
Get Help and Manuals for this Campbell Scientific item
This item is in your list!
View All Support Options Below
Free Campbell Scientific SC532A manuals!
Problems with Campbell Scientific SC532A?
Ask a Question
Free Campbell Scientific SC532A manuals!
Problems with Campbell Scientific SC532A?
Ask a Question
Popular Campbell Scientific SC532A Manual Pages
SC532A CS I/O Peripheral to RS-232 Interface - Page 2
... is warranted by CAMPBELL SCIENTIFIC, INC. Campbell Scientific will not process any CAMPBELL SCIENTIFIC, INC. Campbell Scientific reserves the right to the customer at the customer's expense. This warranty is incomplete, the product will be returned to refuse service on the outside of product receipt or is in it. directly. Affiliate companies handle repairs for special, indirect...
SC532A CS I/O Peripheral to RS-232 Interface - Page 3
Operation 3
6. DC Cable for links to the printed version of Contents
PDF viewers note: These page numbers refer to specific sections.
1. Specifications 2
4. Pin Description A-1
B. SC532A Power Supply Connector 5 2. CSI Peripherals and Their Maximum Operating Current Requirements ....5 3. Hardware Connections 3
5. Connection Block Diagram 3 3. DTE 25 Pin Configuration ...
SC532A CS I/O Peripheral to RS-232 Interface - Page 5
...
The factory setting is "SC532" which is appropriate for any listed peripheral. The SC12 cable connects the SC532A 9-pin female D-Sub labeled "PERIPHERAL" to certain Campbell Scientific datalogger peripherals including...satellite transmitter. The SC532A is for remote sites lacking 120 VAC. The SC532A has an internal jumper that selects either "SC532" or "PROG" mode. SC532A Case Top
1 ...
SC532A CS I/O Peripheral to RS-232 Interface - Page 6
...: 9-pin D-Subminiature Female connects to peripheral through SC12 Two Peripheral Connector Cable supplied with the SC532A.
4 5/8 x 1 3/4 x 1 inches (allow up to 1 1/4 inches extra on AC adapter in use (12 VDC unregulated with AC adapter
2 High ≥ 3.5 V
Low ≤ 0.5 V; Specifications
Input voltage (to POWER jack)
Output voltages
Current available to 5 V peripheral Current available to...
SC532A CS I/O Peripheral to RS-232 Interface - Page 7
... Hardware Connections
Figure 2 shows the connection from a Campbell Scientific peripheral to RS232 levels (−10V and +10V respectively) by the SC532A. Operation
A CSI peripheral's logic levels (0V low, 5V high) are not using PC208 or PC208W Datalogger Support Software. Read the specific peripheral manual for peripherals.
The SC532A supplies regulated 5 VDC and unregulated 12 VDC...
SC532A CS I/O Peripheral to RS-232 Interface - Page 8
...dataloggers lacking 12 V on the outer sleeve.
The correct barrel connector polarity is 17 VDC!
4
SC532A 9-Pin Peripheral to be shared with a DB9 for connection to the 12 V and power ground ...power to power ground terminal. CAUTION
Before plugging power connector into SC532A, if you have 1) the 14291 field cable, 2) replaced the factory AC adapter, or 3) built your own dc power ...
SC532A CS I/O Peripheral to RS-232 Interface - Page 9
SC532 mode (factory default) B. PROGram Seimac SCD/Argos satellite transmitter
5 is 5.5mm (0.216 in .) or more
TABLE 2. SC532A Jumper Guide
P4 Jumper A. SC532A Power Supply Connector
Barrel Connector Polarity and Size
Inner ... 160 mA < 140 mA < 160 mA < 180 mA < 700 mA
TABLE 3. SC532A 9-Pin Peripheral to 17 VDC (see Section 2) (−) GND
O.D is 2.5mm (0.098 in.) Sleeve length = 11...
SC532A CS I/O Peripheral to RS-232 Interface - Page 10
SC532A 9-Pin Peripheral to 9-Pin RS232 Interface This is a blank page.
6
SC532A CS I/O Peripheral to RS-232 Interface - Page 11
The pin descriptions of the SC532A
PC CONNECTOR 9-PIN D-SUB FEMALE
PIN I/O DESCRIPTION
1
I
not used
2
O
RX
3
I
TX
4
DTR
5
GND
... IBM-PC serial port. SC532A Pin Descriptions
PIN = Pin number I = Signal Into the SC532A 0 = Signal Out of the SC532A PC and PERIPHERAL connectors are listed in Table A-2 or A-3
A-1
TABLE A-1.
Pin Description
The SC532A 9-pin female port is ...
SC532A CS I/O Peripheral to RS-232 Interface - Page 12
... line to
control the peripheral's ME and CLK/HS line.
22 RING I
Function
Carrier Detect Receive Data Transmit Data Data Terminal Ready Signal Ground Data Set Ready Request to Send Clear to this
point. TABLE A-3. Pin Description
TABLE A-2.
Appendix A. DTE 25 Pin Configuration
PIN= ABR I = O =
25-pin number = Abbreviation for the...
Campbell Scientific SC532A Reviews
Do you have an experience with the Campbell Scientific SC532A that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.
Earn 750 points for your review!