Campbell Scientific HC2S3 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
This item is in your list!
View All Support Options Below
Free Campbell Scientific HC2S3 manuals!
Problems with Campbell Scientific HC2S3?
Ask a Question
Free Campbell Scientific HC2S3 manuals!
Problems with Campbell Scientific HC2S3?
Ask a Question
Popular Campbell Scientific HC2S3 Manual Pages
HC2S3 Temperature and Relative Humidity Probe - Page 1
HC2S3 Temperature and Relative Humidity Probe
Revision: 10/12
Copyright © 1990-2012 Campbell Scientific, Inc.
HC2S3 Temperature and Relative Humidity Probe - Page 3
... specifications, electrical connections to any special, indirect, incidental, and/or consequential damages." are warranted by Campbell Scientific, Inc. ("Campbell") to the limits extended by Campbell, are re-sold by the original manufacturer. Products not manufactured, but that are warranted only to be the sole and exclusive remedy under normal use and service for installation...
HC2S3 Temperature and Relative Humidity Probe - Page 4
...to the customer at www.campbellsci.com/repair. The following contact information is :
CAMPBELL SCIENTIFIC, INC. Campbell Scientific's shipping address is for US and ...Campbell Scientific reserves the right to refuse service on products that were exposed to contaminants that may not be returned to process any returns until we receive this number clearly on the outside of the problem...
HC2S3 Temperature and Relative Humidity Probe - Page 7
... Local fire codes may preclude its calibration card are shipped in a small box, with the shipping company.
• The model number and ...Campbell Scientific applications engineer.
• Although the HC2S3 is a rugged, accurate temperature/RH probe that parts are available in air. If damage to U.L. 94 H.B. and will support combustion in the remaining sections.
2. Introduction
The HC2S3...
HC2S3 Temperature and Relative Humidity Probe - Page 10
Open Short Cut and click on New Program.
2. Select a datalogger and scan interval.
4 Use SCWin Short Cut to Program Datalogger and Generate Wiring Diagram
The simplest method for programming the datalogger to measure the HC2S3 is to use Campbell Scientific's SCWin Short Cut Program Generator. 1. Model HC2S3 Temperature and Relative Humidity Probe
4.2 Step 2 -
HC2S3 Temperature and Relative Humidity Probe - Page 13
... level single-ended voltage measurements, primarily with Campbell Scientific dataloggers.
The HC2S3-L has a user-supplied cable length and several cable termination options. Temperature range and other default settings can be changed as described in the connector interface provided with an 11 foot cable. Model HC2S3 Temperature and Relative Humidity Probe
5. A special Rotronic...
HC2S3 Temperature and Relative Humidity Probe - Page 14
... part.
Specifications
Features:
• Well-suited for long-term, unattended applications • Accurate and rugged • Compatible with the RAWS-F Quick Deployment Remote Automated Weather Station and can terminate in .) 10 g (0.35 oz)
Polyethylene or Teflon (optional, ordered separately)
8 length and terminates in . The CWS900 enables the probe to a Campbell Scientific...
HC2S3 Temperature and Relative Humidity Probe - Page 15
Model HC2S3 Temperature and Relative Humidity Probe
Power Consumption:
HC2S3 Temperature and Relative Humidity Probe - Page 17
... measurement heights:
1.5 m (AASC) 1.25 to the cable by long cable lengths.
11 Model HC2S3 Temperature and Relative Humidity Probe
7. Installation
7.1 Siting
Sensors should be housed in the Quickstart section).
7.3 Wiring
Connections to the 43502 product manual for a discussion on errors caused by aligning the keyed connectors, pushing the connectors together and tightening...
HC2S3 Temperature and Relative Humidity Probe - Page 19
...enclosures, RAWS-P stations, and RAWS-F stations include a datalogger program. H Differential Input - H
Differential Input -
H Differential Input - Model HC2S3 Temperature and Relative Humidity Probe
TABLE 7-2. Connections for programming information if using VoltSE() instructions. The temperature and relative humidity signals from SW 12V CTRL to a CS110 Electric Field Meter, the probe...
HC2S3 Temperature and Relative Humidity Probe - Page 23
Please contact Campbell Scientific if your program must be executed every 1 second
CallTable (Table1)
NextScan...)
'add additional instructions to warm-
'Measure HC2S3 temperature 'Measure HC2S3 relative humidity 'Turn off probe
7.4.2 Example Programs using single-ended measurements in SequentialMode. The program sets relative humidity equal to 100, and indicate a problem with the sensor ...
HC2S3 Temperature and Relative Humidity Probe - Page 25
...19 Model HC2S3 Temperature ...Set Output Flag High (Flag 0)
9: Set Active Storage Area (P80)
1: 1
Final Storage Area 1
2: 101
Array ID
10: Real Time (P77) 1: 1220 Year,Day,Hour/Minute (midnight = 2400)
11: Average (P71) 1: 1 Reps 2: 3 Loc [ AirTC ]
12: Sample (P70) 1: 1 Reps 2: 4 Loc [ RH ]
7.5 Measuring Probes with Long Cables
For cable lengths longer than 6.1 m (20 ft), Campbell Scientific...
HC2S3 Temperature and Relative Humidity Probe - Page 26
... the manual.
20 Please refer to ground at the beginning of the pollutant influence.
Before putting on the replacement filter check the alignment of the sensors with 12 V. Model HC2S3 Temperature and Relative Humidity Probe
The signal reference (yellow) and the power ground (gray) are not enough inputs available on the datalogger to Campbell Scientific for...
HC2S3 Temperature and Relative Humidity Probe - Page 27
... range code for the single-ended or differential measurement instruction is jumpered to check the output voltage for temperature and relative humidity on Automated Weather Stations, v. 9, No. 4 October, 1985. (www.stateclimate.org/publications/state-climatologist/NOAA-NCYSCBOOKS-SC77097/00000029.pdf)
EPA, 2000: Meteorological Monitoring Guidance for probes purchased through Campbell Scientific...
HC2S3 Temperature and Relative Humidity Probe - Page 31
... Data bits: 8 Stop fits: 1 Flow Control: none
Logical Levels: Logical 0: Changing the HC2S3 Settings
B.1 HC2S3 Default Settings
The HC2S3 probe has the following default settings, which can be downloaded from Rotronic's website www.rotronic-usa.com. Additional information can be found in Rotronic's User Manual: E-M-HC2 Probes-VXXXX, which can be changed as described in the following...
Campbell Scientific HC2S3 Reviews
Do you have an experience with the Campbell Scientific HC2S3 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.
Earn 750 points for your review!