Brother International VX1445 Support and Manuals
Get Help and Manuals for this Brother International item
This item is in your list!
View All Support Options Below
Free Brother International VX1445 manuals!
Problems with Brother International VX1445?
Ask a Question
Free Brother International VX1445 manuals!
Problems with Brother International VX1445?
Ask a Question
Brother International VX1445 Videos
Popular Brother International VX1445 Manual Pages
Operation Manual - Page 2
...; Do not use in the instruction manual:
• To unplug the ...where oxygen is approved for examination, repair, electrical or mechanical adjustment.
...to the nearest authorized Brother dealer or service center for use ...extension cords. Do not use an extension cord.
• Always unplug your work area clear:
• Never operate the machine with any other part...
Operation Manual - Page 3
... follow careful instruction when freehand stitching so that you do not deflect the needle and cause it must be kept out of the reach of children or disposed of the operation manual to clean the case. Do not use as described in this manual. If the problem persists, please consult your local authorized Brother Service Center...
Operation Manual - Page 4
...and knowledge, unless they have been given supervision or instruction concerning use by persons (including children) with the ...instruction concerning use of replacing the plug fuse, use .
FOR USERS IN EUROPEAN COUNTRIES This appliance can be made by ASTA to obtain the correct lead.
3 Children should contact your authorized Brother Service Center to
BS 1362, i.e. SAVE THESE INSTRUCTIONS...
Operation Manual - Page 5
...Replacing the needle 8 Changing the presser foot 10
THE CONTROLS 11
Pattern selection dial 11 Patterns and stitch names 11 Reverse sewing lever 12
THREADING THE MACHINE 13
Winding the bobbin 13 Lower threading 15 Lower threading (for models equipped with a quick-set... Precautions on storing the machine 40 Cleaning 40
TROUBLESHOOTING 42 INDEX 45
4 USING ATTACHMENTS AND APPLICATIONS ...
Operation Manual - Page 6
...-021
4 Button sewing foot "M"
XE2137-001
5 Walking Foot
SA107 F034N: XC2165-002
No. Part Code Americas Others 3-piece set: XE5328-001 2-piece set (90/14 needle)
6 Screwdriver
7 Foot controller
Note
● The included accessories vary depending on the machine model.
Part Name
Part Code Americas Others
1 Zigzag foot "J" (on machine)
XC4901-121
2 Buttonhole foot "A"
X59369-321...
Operation Manual - Page 7
... 27) This controls the tension of thread for 220-240V area
The foot controller part code differs depending on and off. C Buttonhole fine-adjustment screw (Page 34)
D Pattern selection dial (Page 11) Rotate the dial in either direction to manually raise and lower the needle. Contact your Brother dealer or the nearest authorized Brother Service Center.
Operation Manual - Page 8
...damage the cord and cause fire or electric shock. Connect the power supply plug to install the proper outlet. To reduce the risk of time. KNOWING YOUR SEWING MACHINE
USING YOUR... power first. If the cord or plug is damaged, take the machine to your authorized Brother Service Center for repairs before continuing use • When the machine does not operate correctly due to be cut,...
Operation Manual - Page 14
... holding the thread from other bobbins may tangle on the thread guide. If you , in the groove on the spool pin. SA156 is set incorrectly, the thread may cause damage to the machine. Actual size
11.5 mm (7/16 inch)
This model
Other models
1
1 Pull the thread in completely.
2 3
1 Pre-tension disk
2 Bobbin winder shaft...
Operation Manual - Page 17
...bobbin 2 with thread. Follow steps 1 to 4 from "Lower 1 threading" on certain models. This feature is not correctly inserted through the slit (1 and 2). When sewing gathers or ...Install the bobbin wound with your right hand as shown, guide the
thread through the tension-adjusting spring of the bobbin case, it with a quick-set bobbin)
Replace the bobbin cover. Lower threading (for models...
Operation Manual - Page 19
... feed the upper thread.
● If you incorrectly feed the thread you may cause sewing problems.
18
toward you (counterclockwise) so that the spring in the groove catches the thread. While... upper thread as shown in the 6 following illustration.
1
4 2
1 1 Needle bar thread guide
53
Make sure you guide the thread through 7 the thread take-up lever from right to left
as shown in the following...
Operation Manual - Page 20
... "Upper threading" on page 17. KNOWING YOUR SEWING MACHINE
Using the needle threader (for models equipped with a 65/9 home sewing machine needle. However, the needle threader cannot be used...threader lever 3 Guide
Pull down the needle threader lever as 5 much as possible, and then turn the lever
toward the back of the machine (away from "Upper 1 threading" on certain models. Make sure that...
Operation Manual - Page 22
...as described in the 2 direction of the arrow, and leave it there
without drawing up the bobbin thread. Replace the bobbin cover.
4
2
1 Upper thread 2 Lower thread
Pull out about 10 cm (4 inches) of ...removed. Pull on the upper thread to lower and then raise the needle.
■ For models equipped with a quick-set bobbin
You can draw up the lower thread by hand to draw up the 2 lower thread....
Operation Manual - Page 41
...extended period of time without using the machine, and contact your authorized Brother Service Center or the nearest authorized Brother Service Center. This machine was manufactured with the necessary amount of this ...In order to prevent damaging this machine, it must not be oiled by condensation. If problems occur, such as shown
in any of the locations described below, otherwise damage to the...
Operation Manual - Page 43
.... Replace the needle plate. The bobbin case is incorrectly installed.
... http://support.brother.com ".
Use the screwdriver to sew.
breaks. Lightly guide the ...Brother Solutions Center offers the latest FAQs and troubleshooting tips. The needle
want to
-
authorized Brother Service Center.
If the problem persists, contact your retailer or the nearest authorized Brother Service...
Operation Manual - Page 44
... is bent or blunt. The needle is set incorrectly. Contact your retailer or the nearest authorized Brother Service Center. Replace the bobbin. Use a bobbin that has ...install the needle. Attach the presser foot holder properly. The needle is incorrect. Bobbin is not being sewn, the fabric is set incorrectly.
APPENDIX
Symptom ▲
The upper thread breaks. Replace...
Brother International VX1445 Reviews
Do you have an experience with the Brother International VX1445 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Brother International yet.
Earn 750 points for your review!