iRobot Verro 300 Support Question
iRobot Verro 300 Support Question
Find answers below for this question about iRobot Verro 300.Need a iRobot Verro 300 manual? We have 1 online manual for this item!
Question posted by polkadot11 on May 1st, 2012
Irobot Verro 300 Pool Cleaner
motor is running but not pumping water in order to move /run
Current Answers
Related iRobot Verro 300 Manual Pages
Product Manual - Page 2
... order to avoid hazards. Mishandling the unit can result in the pool all the time. Please keep the plug away from the water.
Do not leave the cleaner in leakage of the pool... cleaner from contact with the local and national wiring rules (electrical code). Do not plug the Power Supply in the pool.
Safety Notes
WARNING: Your cleaner should be consistent with water.
iRobot Verro ...
Product Manual - Page 3
... immersed in water. Allow the cleaner to lift Verro from the pool. Do not switch the pool cleaner ON if it in the rain. This will allow the motors to 20 minutes following the end of warranty. It will result in loss of its cleaning cycle. Do not force the floating power cord plug. www.irobot.com Operating...
Product Manual - Page 4
... and then press the reset button.
iRobot Verro Owner's Manual Important: Failure to move or clean properly. If the filter bag is opened for regular maintenance.
Tips
Tip Clean the filter bag regularly.
Verro uses the force of the water pumped through its filter bag to properly store Verro will result in a dry place out of...
Product Manual - Page 6
... Cord 18. Fixed Axle Housing 19. 2" Wheel 20. Handle 22. Locking Tab
iRobot Verro Owner's Manual Jet Tube 5. Filter Screen 6. Jet Nozzle 25. Jet Valve Housing 17. Wheel Hubcap 23. Star Washer 24. Cable Grommet 2. Filter Bag 13. Bottom Lid Assembly 15. Square Foam Float 12. Pump Motor 7. Steering Axle Housing 11.
Anatomy
Parts List
1.
Product Manual - Page 8
... Supply in a dry area at least 12 feet from the pool.
3.5m/12ft
4 Plug the floating power cord into a GFCI outlet. Turn Verro over the surface of the water, ensuring that it is not tangled or kinked.
2
Place Verro upside down in the pool and rock it from side to side to allow it to...
Product Manual - Page 9
... time control dial to clean your pool.
8
After approximately two hours, Verro will turn off. To stop and the Power Supply light will stop Verro before the end of the cleaning cycle, switch the Power Supply OFF.
www.irobot.com The light on the Power Supply will illuminate and Verro will start to 30 seconds...
Product Manual - Page 10
... out of the water. CAUTION: Removing Verro by its floating power cord may be damaged by rain.
10 iRobot Verro Owner's Manual
Using Verro (cont...)
9 Wait 20 minutes before removing Verro from the pool to allow the pump motor to turn the Power Supply OFF and unplug it from the power outlet before removing the cleaner from the pool.
10 Unplug...
Product Manual - Page 11
... force of the pool efficiently.
Each time it changes direction, Verro automatically alters it course slightly so that it . www.irobot.com 11 The pump motor also drives two high-pressure jets under the robot that loosen dirt and attached particles, which are trapped.
How Verro Works
iRobot Verro uses a powerful motor to draw 80 gallons of water per minute...
Product Manual - Page 12
... a different type of the pool to the waterline on the other side at the widest point, waiting approximately two seconds on each side.
Once the time control dial has been set to consistently not reach the waterline, or starts moving more slowly, try cleaning the filter bag.
12 iRobot Verro Owner's Manual turning...
Product Manual - Page 13
... Filter Bag
It is very important to clean Verro's filter regularly in order to move around, a clogged filter can significantly reduce Verro's effectiveness. Since Verro uses the water it pumps both to clean and to keep the plug away from water.
2 Place Verro upside down on a towel (to clogging from the pool.
The mesh filter bag is more than...
Product Manual - Page 14
Make sure the tabs click into place.
14 iRobot Verro Owner's Manual If this does not remove all visible dirt, machine wash the bag using cold water on the inside out and rinse away any accumulated debris with a...filter bag inside and the smooth, shiny surface is on the outside and place it until the water is on the gentle cycle. Gently agitate and squeeze the bag while rinsing it back on ...
Product Manual - Page 16
... the Detangler in your pool in the handgrip so that you walk.
4 If the cord is not fully untwisted by the time it a few more turns by hand.
16 iRobot Verro Owner's Manual However, if the cord tangles or kinks, and will not lie properly on the surface of the water, it may be...
Product Manual - Page 17
......)
Cleaning the Impeller Verro uses an impeller to pump water up through the vacuum intakes at the bottom of the motor. www.irobot.com 17 If this impeller becomes fouled by hair, string, etc. If you notice that Verro is not cleaning well or that it will reduce the amount of water Verro can pump and may reduce the...
Product Manual - Page 18
It may be
helpful to use a small flashlight to see better.
7 Replace the jet valve port. 8 Replace the screws.
18 iRobot Verro Owner's Manual 6 Using the bent paper clip, hook the material fouling the impeller.
Product Manual - Page 19
...glued in place. 4 Clear any form
of water like power washers to clean as it from the holders at each end. www.irobot.com 19
If Verro is not doing a good job of loosening ...plug away from contact
with water.) Unplug the floating power cord from the Power Supply. 2 Examine the clear tubes for obstructions. 3 Remove the tube by flushing the tube with cold water. 5 Reinsert the tube ...
Product Manual - Page 20
..., above) in order to change direction. Check to redirect the flow of water so that is a flap just inside each vacuum intake at the bottom of water from a hose into... the jet valve port. To clean the direction baffle, direct a high-pressure jet of the robot. If they do not, remove any dirt or debris that it swings freely in both directions.
20 iRobot Verro...
Product Manual - Page 21
...
Check wheels and axles for dirt and debis. Verro does not cover entire pool
The pump impeller is Clean the pump impeller. (p. 17) fouled by a dirty or clogged filter bag. If rinsing the filter bag by hand with Verro are caused by dirt and debris
www.irobot.com 21 Do not machine dry the filter bag...
Product Manual - Page 22
... dirt and debris. The pump impeller is Clean the pump impeller. (p. 17) fouled by dirt or debris
Verro waits too long at side of pool before reaching end of pool
Likely Cause The filter bag... pump impeller is fouled by dirt or debris
Check the direction baffle. (p. 20)
Clean the filter bag. (p. 13)
Check the flaps in the vacuum intakes. (p. 20)
Clean the pump impeller. (p. 17)
22 iRobot Verro ...
Product Manual - Page 24
... • Saturday 9AM - 6PM Eastern Time
24 iRobot Verro Owner's Manual
iRobot Customer Care
Please visit our web site at 877.855.8593 iRobot Customer Care Hours: • Monday - We would like to hear from you still need assistance, call our customer care representative at www.irobot.com for support tips, frequently asked questions or...
Product Manual - Page 28
Pricing and availability subject to change. iRobot is a registered trademark and Verro is a trademark of iRobot Corporation. All rights Reserved.
3001.07 All rights reserved. Register your iRobot®Verro™ today. Shipping and handling not included.
© 2007 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. Cover photo © Veer Incorporated 2002 - 2005. SAVE ...
Similar Questions
Irobot Verro 500 Pool Cleaner
I need the bottom lid assembly to attach the bag. Our is cracked
I need the bottom lid assembly to attach the bag. Our is cracked
(Posted by pbdennis 1 year ago)
I Robot 500 Pool Cleaner
My pool cleaner goes one direction hits the wall and then wont go back the other direction any more....
My pool cleaner goes one direction hits the wall and then wont go back the other direction any more....
(Posted by trevorerhardt 2 years ago)
I Need A Motor For My Irobot Verro Series 300 Where Can I Get One
(Posted by deepon5953 3 years ago)
Verro 500 Pool Cleaner
Have a unit in which the pump starts up but the unit wont propel itself. Have checked the rollers be...
Have a unit in which the pump starts up but the unit wont propel itself. Have checked the rollers be...
(Posted by piperfarms 6 years ago)
Irobot Verro 300 Troubleshoot
Verro runs for 15 seconds only then stops. No blockage identified.
Verro runs for 15 seconds only then stops. No blockage identified.
(Posted by lakehio1 11 years ago)