eMachines E527 Support Question
eMachines E527 Support Question
Find answers below for this question about eMachines E527.Need a eMachines E527 manual? We have 1 online manual for this item!
Question posted by pvnmtirur on August 5th, 2012
Booting Problem
E527 laptop starting with continues beep sound and some times take long time to start up
Current Answers
Answer #1: Posted by baklogic on August 5th, 2012 11:31 AM
baklogic
Member since:
June 28th, 2012 Points: 442,480
Member since:
June 28th, 2012 Points: 442,480
Sometimes a sticking key will beep continuously.
I suspect though it could well be a ram stick playing up.
You might try removing power supply, remove battery
Turn laptop over and remove the memorycover on the rear panel -usually held by one or two small screws- then carefully use your fingernails to release the two clips on each ram stick, slide them out, and reseat them.Do not tough the metal contact portion - use surgical gloves if you have some to avoid static to the internal parts.
Here is a video by crucial one of the top ram sellers, as I cannot find a picture of yours - all very similar.
25 years playing with computers/laptops, software, and 10 years a geek/nerd -always learning
Related eMachines E527 Manual Pages
User Guide - Page 7
... the device the above separation distance instructions are positioned at least 1.5 centimeters (5/8 inches) away from lightning, do not try to the figure below).
Consult your laptop under the following conditions. Remember to this equipment during lightning or thunderstorms.
Warning! This device meets RF exposure guidelines when used normally, and it may...
User Guide - Page 13
...your computer. Note: Viewing the file requires Adobe Reader.
In addition it :
1 Click on
Start, All Programs, eMachines Documentation.
2 Click on such subjects as eMachines Recovery Management, using your ... etc. This guide contains detailed information on User Guide. poster helps you get started with language such as the User Guide mentioned below the LCD screen beside the ...
User Guide - Page 14
... to heavy shock or vibration. • Do not expose the computer to take care of the following:
• Use the Windows shutdown command
Click on Start
then click on Shut Down.
• Use the power button
You can also put the computer in should not exceed the fuse rating.
Carefully route...
User Guide - Page 18
... passwords
17
Expanding through options
18
Connectivity options
18
Built-in network feature
18
Universal Serial Bus (USB)
18
Installing memory
19
BIOS utility
20
Boot sequence
20
Enable disk-to RF fields (RSS-102)
36
LCD panel ergonomic specifications
36
User Guide - Page 21
.... English
3
Windows keys
The keyboard has two keys that perform Windows-specific functions. it launches the Start menu. Key
Description
Windows key
Pressed alone, this key has the same effect as clicking on your ... Windows Flip 3-D
Application key
Note: Depending on the Windows Start button; It can also be used with other keys to provide a variety of functions:
< >: Open or close the...
User Guide - Page 23
... and deselect the Mute all option.
• The volume level may be too low. Nothing appears on the power, but the computer does not start or boot up.
If it is not lit, no power is heard from the computer. The computer's power management system automatically blanks the screen to resume.
Press...
User Guide - Page 25
English
7
To start the recovery process: 1 Restart the system. 2 While the eMachines logo is showing, press + at the same time
to enter the recovery process. 3 Refer to the onscreen instructions to perform system recovery. This feature occupies 15 GB in a hidden partition on your hard disk.
Important!
User Guide - Page 28
... release latch to a mains power outlet. You are advised to start the next day with the computer turned off results in a cool.... • Store the battery pack in a significantly faster charge time. Plug the AC adapter into the computer, and connect to release... battery to see the battery's present charge level. You can continue to operate your computer on the taskbar to self-discharge faster...
User Guide - Page 30
... steps to disconnect your computer from external accessories: 1 Save any media, floppy disks or compact disks from the drive(s). 3 Shut down the computer: Click on Start, Turn Off Computer, then click on Turn Off Or: You can now safely take the computer anywhere you go within short distances, for example, from...
User Guide - Page 34
...Setting these passwords creates several different levels of this password with password checkpoints on boot-up and resume from unauthorized access. Combine
the use of protection for maximum... immovable object such as a table or handle of this password with password checkpoints on Boot secures your computer and data:
• Supervisor Password prevents unauthorized entry into the notch...
User Guide - Page 35
...try again. You have three chances to shut down the computer. Then turn on boot parameter is
enabled, a prompt appears at boot-up .
• Type the User Password and press to use the computer....When the Supervisor Password is set, a prompt appears when you press
to enter the BIOS utility at boot-up .
• Type the Supervisor Password and press to access the BIOS utility. If you
enter ...
User Guide - Page 38
... configuration problems, you do not need to Enabled. Enable disk-to-disk recovery
To enable disk-to set the boot sequence in the BIOS utility, activate the BIOS utility, then select Boot from the... then select Main from the categories listed at the top of the screen. Find Password on boot, activate the BIOS utility, then select Security from the categories listed at the bottom of the ...
User Guide - Page 43
You can also reinstall applications and drivers for your Gateway system. 1 Click on Start, All Programs, eMachines, eMachines Recovery Management. 2 Switch to the Restore page by clicking Restore.
3 You can choose to complete the process. English
25
Restore
The ...
User Guide - Page 44
...will reboot. 3 After rebooting, when the eMachines logo shows, press the F12 key to open the BOOT Menu.
4 Here you will be installed from the recovery disc.
6 Insert the second recovery disc when ...complete. Do this before rebooting your previously burned backup discs, you can select which device to boot from.
5 Use the arrow keys to complete the restore.
7 Remove the recovery disc from ...
User Guide - Page 45
If you prefer to set the boot priority for long-term use, you can set system parameters.
3 Use the left and right arrow keys to select the Boot submenu.
4 Use the up and down arrow keys to select the optical drive device. 5 Use the F6 key to move the optical drive device to ...
User Guide - Page 47
... interface error
Contact your dealer or an authorized service center.
Error messages
If you solve problems.
If the system reports an error message or an error symptom occurs, see "Error messages...POST) to enter the BIOS utility, then press Exit in the BIOS utility to reboot. Disk boot failure
Insert a system (bootable) disk into the floppy drive (A:), then press to open the computer...
User Guide - Page 48
Some problems may be solved using the BIOS utility. 30
If you still encounter problems after going through the corrective measures, please contact your dealer or an authorized service center for assistance. English
User Guide - Page 50
... a la norme NMB-003 du Canada. If possible, they do, you will notify you in advance to give you must provide this equipment. If the problem is causing the...
User Guide - Page 51
However, due to different numbers are spaced such that there is not less than 5 seconds between the end of one attempt and the beginning of problems, you should difficulties arise in the first instance.
The associated equipment shall be no more information about applicable countries, please refer to the Public Switched ...
User Guide - Page 52
... is produced with such devices. This has no guarantee that Telecom lines will always continue to support pulse dialing.
7 Use of pulse dialing, when this product may or....
General
This product complies with pulse dialing while the Telecom standard is DTMF tone dialing. Should such problems occur, the user should NOT contact the telecom Fault Service.
8 This equipment may not provide for the...
Similar Questions
How Do I Get My E527 Laptop To Do A Factory Restore
ive tried the left alt f10 thing and it didnt work
ive tried the left alt f10 thing and it didnt work
(Posted by revalutionevolution123 9 years ago)
I Have An Emachines E527 Laptop There Is No Caplock Indicator?
I HAVE A EMACHINES E527 LAPTOP ITS GREAT ONE PROBLEM THERE IS NO LAPTOP INDICATOR SO I NEVER KNOW ...
I HAVE A EMACHINES E527 LAPTOP ITS GREAT ONE PROBLEM THERE IS NO LAPTOP INDICATOR SO I NEVER KNOW ...
(Posted by hillgrovehouse 11 years ago)
I Have E527 Laptop And It Is Showing Pluggin Ur Web Cam What Is The Problem ?plz
(Posted by harrysingh90417 11 years ago)
My Emachine 725 Problem
my e machine laptop is making a beeping sound when i open it and presssing f12 it will go to windows...
my e machine laptop is making a beeping sound when i open it and presssing f12 it will go to windows...
(Posted by alberthall77 12 years ago)
Password
I´ve bought this laptop and I´ve losed my password. The name is Carmen. The starter pa...
I´ve bought this laptop and I´ve losed my password. The name is Carmen. The starter pa...
(Posted by faraonlaviana 12 years ago)