Zenith SL-5798-WH-A Support Question
Zenith SL-5798-WH-A Support Question
Find answers below for this question about Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light.Need a Zenith SL-5798-WH-A manual? We have 1 online manual for this item!
Question posted by hswirsky on December 9th, 2013
Sl 5798 Sensor Light
how doesa the sl 5798 sensor light shut off
Current Answers
Related Zenith SL-5798-WH-A Manual Pages
User Guide - Page 1
...
© 2007 HeathCo LLC
598-1309-01 x
Until Dawn*
x
3, 6 Hr.
DualBrite® Triple Halogen Motion Sensing Light
Model 5798
Features
• Turns on lighting when motion is intended for use with the enclosed
gasket and with a junction box marked for the circuitry to Dawn
LAMP MODE
Sensor Light Control
3 Wire Connectors
Put the LAMP MODE switch in wet locations.
User Guide - Page 2
... stick on as shown in the AUTO mode. The motion sensing features will be rotated as shown below. Light starts dim and gradually increases to work as described in the 1, 5, or 20 position.
... Light flashes on then off for proper under eave installation, the sensor head must be in the next two steps for one second...
User Guide - Page 3
...counterclockwise and
wire connectors.
Secure the fixture to the junction box ground wire.
598-1309-01
the cover plate.
Wire the Light Control
Mount the Light Control
❒ Place the... turns, turn power off at least 1" (2.5 cm) from the sensor.
Tighten set screw 2 full
turns with a small flat-head screwdriver.Turn shade counterclockwise and remove. ❒ To remove bulb,...
User Guide - Page 4
... traffic may trigger the control.
• Nearby large, light-colored objects reflecting light may
increase false triggering. ❒ Secure the sensor head by
tightening the clamp screw.
RANGE set too high may trigger the shut-off feature.
T4, 100W maximum G8 halogen bi-pin 120 VAC DualBrite® Timer. . . . . Motion
Motion
❒ Turn the RANGE control to the medium...
User Guide - Page 5
...) for this mode. You may be sensing small animals or automobile traffic (re-aim sensor). 2. Sensor is normal under these conditions. A lamp is turned off . (Reposition the lamps away from the sensor or nearby objects).
2.
Light switch is positioned too close to cover desired area. Lights come on and off.
1. Light control is normal in the Test...
User Guide - Page 6
... by this warranty in its entirety. Some states or provinces do not allow the exclusion or limitation of any obligation to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by factory defective parts or workmanship will void this warranty. You may not apply to other...
Similar Questions
Heath Zenith Motion Sensor Light Wont Turn Off
(Posted by Tiighchairu 10 years ago)
Sl-5525 Sensor Tested Ok But Won't Turn Light On In Auto Mode?
(Posted by simonikt 11 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
Would You Help Me Reset My Sensor Light?
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
(Posted by ofallonbob 12 years ago)