Zenith SL-5512-BZ-B Support Question
Zenith SL-5512-BZ-B Support Question
Find answers below for this question about Zenith SL-5512-BZ-B - Heath - Quartz Halogen Motion-Sensing Twin Security Light.Need a Zenith SL-5512-BZ-B manual? We have 1 online manual for this item!
Question posted by drwoggon on December 6th, 2014
Zenith Hologen Motion Sensor Light
How do I adjust it so that both lights come on with motion and not just one>
Current Answers
Answer #1: Posted by TommyKervz on December 9th, 2014 3:11 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
please download user manual below and read page 3&4
Related Zenith SL-5512-BZ-B Manual Pages
User Guide - Page 1
... lighting off. • DualBrite® Timer. • Photocell keeps the lighting off for one second
then back on the sensor bottom
to Dawn
Sensor Light Control...
Mounting Strap
Gasket
2 Halogen Bulbs
Light Shield
MANUAL MODE
Manual mode only works at dawn.
DualBrite® Twin Halogen Motion Sensing Light
Model SL-5512
Requirements
• The light control requires 120-volts ...
User Guide - Page 2
... ground. For under eave operation, remove the protective backing from the light shield and stick on as described in this feature.
The motion sensing features will continue to avoid the risk of the ball joint, loosen the clamp screw and push the sensor back into the ball joint.
Do not aim at objects closer...
User Guide - Page 3
...breaker or fuse.
❒ Remove the existing light fixture.
❒ Install mounting strap to junction ... wires shown as shown. Twist together and secure with silicone. CAUTION: Do not cut any...not installed on the mounting strap.
❒ Adjust the lamp holders by loosening the lock nuts
&#...above illustration.
595-5575-09
from the sensor.
fixture cool.
❒ Make sure the ...
User Guide - Page 4
... traffic may trigger the control.
• Nearby large, light-colored objects reflecting light may
increase false triggering. ❒ Secure the sensor head by
tightening the clamp screw. Do not overtighten the screw. Risk of time after
dusk you want the lights to motion directly towards it will detect motion. Do not aim the bulbs at Down for...
User Guide - Page 5
T3, 150W halogen maximum 120 VAC DualBrite® Timer. . . . . Lamp is operating normally under these condi- Re-aim light control to 1, 5, or 10 minutes. The fixture is loose or burned out. 3.
Set control switch to cover desired area. Light control may be sensing small animals or automobile traffic.
2. Relocate light control, or use 3 hr. Dusk-to...
User Guide - Page 6
...), 7:30 AM to store. You may also write* to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by factory defective parts or workmanship will... above limitation or exclusion may also want to other rights which gives you .
Repair service, adjustment and calibration due to : HeathCo LLC P.O. Some states or provinces do not allow the exclusion...
Similar Questions
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Zenith Motion Sensor Light Won't Turn Off
(Posted by matrijone 9 years ago)
Heath Zenith Motion Sensor Light Wont Turn Off
(Posted by Tiighchairu 10 years ago)
Light Stays On All Night
I would like to have the light operate only when sensor senses movement only.
I would like to have the light operate only when sensor senses movement only.
(Posted by acahorvath 13 years ago)
Lights Come Immediatelly And Stay On When It Gets Dark,what Is The Problem?
(Posted by reallyoldmargie 14 years ago)