Zenith SL-5410-GR Support Question
Zenith SL-5410-GR Support Question
Find answers below for this question about Zenith SL-5410-GR - Heath - 110-Degree Motion Sensing Security Light.Need a Zenith SL-5410-GR manual? We have 1 online manual for this item!
Current Answers
Related Zenith SL-5410-GR Manual Pages
User Guide - Page 1
...
Motion Sensor Light Control
As an ENERGY STAR® Partner, Heath...sensor to use Manual Mode, the control must be
wired through a switch. • Some codes require installation by a qualified
electrician. • This product is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • 5410 models have Flash Alert feature (light...
User Guide - Page 2
....
Tighten the clamp screw when done.
598-1303-01 INSTALLATION
Wire the Light Control
For easy installation, select an existing light operated by a wall switch for proper operation and to avoid the risk of the ball joint, loosen the clamp screw and push the sensor back into the ball joint.
For best performance, mount the...
User Guide - Page 3
...light control to the TEST position. Avoid water damage and electrical shock -
NOTE: Sensor has a 1 1/2 minute warm up period before it will detect motion.
Deactivated (Blue)
Mount the Light Control
❒ Align the light...mounting surface with the mounting screws.
❒ If not installed on the circuit breaker and light switch. keep lamp holders below horizontal. To Deactivate the ...
User Guide - Page 4
... area noting where you
Aim Sensor Higher for Short
Coverage
❒ Secure the sensor head by tightening the clamp ...lights to 150 Watt maximum each lamp holder.] Power Requirements. . 120 VAC, 60 Hz Operating Modes. . . . . Move the sensor head up, down will reduce coverage distance.
❒ Loosen the clamp screw in products previously sold.
598-1303-01 Sensing Angle Up to 110...
User Guide - Page 5
...).
5. Daylight turn-off is positioned too close to the sensor or pointed at nearby objects that cause heat to store. sired area.
1. Light control may be sensing small animals or automobile traffic (re-aim sensor).
2. Lights flash on .
Lights come on for this guide. F l o o d ...Available for no apparent reason.
1.
Light control may be installed in the Test mode and warming...
User Guide - Page 6
... a customer uses in its entirety. You may not apply to misuse, abuse or negligence, light bulbs, batteries, and other rights which gives you . Not Covered - REPAIR OR REPLACEMENT SHALL... you. This warranty covers only HeathCo LLC assembled products and is required for inconvenience, installation, setup time, loss of any malfunction caused by this warranty in conjunction with our ...
Similar Questions
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
Conection Of A Sl5410a Motion Sensor
How do we connect the white black and red wire to the incoming 14-2 wire
How do we connect the white black and red wire to the incoming 14-2 wire
(Posted by boblagace 12 years ago)
Would You Help Me Reset My Sensor Light?
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
(Posted by ofallonbob 12 years ago)