Zenith SL-5410-GR Support Question
Zenith SL-5410-GR Support Question
Find answers below for this question about Zenith SL-5410-GR - Heath - 110-Degree Motion Sensing Security Light.Need a Zenith SL-5410-GR manual? We have 1 online manual for this item!
Question posted by jaimitolopez on December 26th, 2017
Necesito El Diagrama De Conecccion De Los Cables La Mia Es Una 5210-a2
1.la desconecte pero no recuerdo como van los cables de nuevo en el sensor hay tres cables y las lamparas dos cada una podrian decirme como hacerlo que no recuerdo
Current Answers
Answer #1: Posted by BusterDoogen on December 26th, 2017 2:21 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
vaya a la página 6 para el diagrama de cableado.
¡ Espero que esto le sea útil!
por favor responda a mi esfuerzo para proporcionarle la mejor solución posible usando la "solución aceptable" y/o los botones "útiles" cuando la respuesta ha demostrado ser útil. Por favor, siéntase libre de presentar más información para su pregunta, si no se proporcionó una solución. ¡ aprecio la oportunidad de servirle!
Related Zenith SL-5410-GR Manual Pages
User Guide - Page 1
... is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • 5410 models have Flash Alert feature (light flashes on
then off for the circuitry...
© 2007 HeathCo LLC
598-1303-01 OPERATION
Motion Sensor Light Control
As an ENERGY STAR® Partner, Heath®/Zenith has determined that this product meets the ENERGY STAR&#...
User Guide - Page 2
... together and secure with Flash Alert feature will reduce coverage distance.
❒ Drill the holes needed to mount the backplate to the junction box. This wire loop should not be rotated as shown in the next two steps for replacement. If the sensor pops out of electrical shock. INSTALLATION
Wire the Light Control...
User Guide - Page 3
... Light Control
❒ Align the light ...sensor
inside the canopy. ❒ Cut the (Blue) wire loop. ❒ Securely attach wire nuts (supplied) to wall or eave.
❒ Turn on the circuit breaker and light... switch. Lock nuts
Keep lamps at circuit breaker or fuse.
❒ Remove the light...
User Guide - Page 4
... is mounted higher than 8 ft.(2.4 m), aiming the sensor down , or sideways to 150 Watt maximum each lamp holder.] Power Requirements. . 120 VAC, 60 Hz Operating Modes. . . . .
Risk of TIME you are when the lights turn on after motion is detected
(1, 5, or 10 minutes). Sensing Angle Up to 110° Electrical Load Up to 60 ft...
User Guide - Page 5
...-
You may be sensing small animals or automobile traffic (re-aim sensor).
2. If the problem persists, call 1-800-858-8501 (English speaking only) for this guide. No Service Parts Available for assistance before returning product to 4:30 PM CST (M-F).
Light control is normal under these conditions).
4. Heat or light from the sensor).
2. Light is in effect...
User Guide - Page 6
... component will be corrected at no charge to you. For a period of two years from state to state or province to misuse, abuse or negligence, light bulbs, batteries, and other equipment and components that a customer uses in its entirety.
Similar Questions
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
Conection Of A Sl5410a Motion Sensor
How do we connect the white black and red wire to the incoming 14-2 wire
How do we connect the white black and red wire to the incoming 14-2 wire
(Posted by boblagace 12 years ago)
Would You Help Me Reset My Sensor Light?
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
I had siding put on and when they took the sensor light SL-5410-A off and put it back on the sensor ...
(Posted by ofallonbob 12 years ago)