Zenith SL-4305-WH Support Question
Zenith SL-4305-WH Support Question
Find answers below for this question about Zenith SL-4305-WH - Heath - Motion-Activated Five-Sided Porch Light.Need a Zenith SL-4305-WH manual? We have 1 online manual for this item!
Question posted by redolds98 on August 26th, 2012
Heath Zenith Sl-4305-wh Wiring Schematic
I would like to deactivate to motion sensor on automatic
Current Answers
Related Zenith SL-4305-WH Manual Pages
User Guide - Page 1
Motion Sensing Porch Light
SL-4305
Features
• Light comes on wait about 1 1/2 minutes for the circuitry to calibrate. Note: When first turned on when motion is detected. • Automatically turns light off. • Photocell keeps the light off for one minute, then back on to TEST. Flip the light switch off during daylight
hours.
Manual mode works only with the ON...
User Guide - Page 2
... m) above the ground. SENSITIVITY
LO - Attach universal mounting bracket to control other lights from this motion sensor fixture.
2. Remove universal mounting bracket from light fixture cover.
2.
HI TESOTN1-T5IM1E0 MIN
Universal Mounting Bracket
Wiring Light Fixture
1. Disassemble Light Fixture
1. Remove two decorative nuts from base.
Universal Mounting Bracket Junction Box Screw...
User Guide - Page 3
... Black White to White Ground to Ground
One Motion Sensing Light
Ground to Ground
Black to Black White to White
Two Motion Sensing Lights (Working Independently)
Other Wiring Options
This fixture can be run in the fixture. Maximum Load for Motion Sensor - 500 Watts
Maximum Lamp Wattage Rating for Light Fixture -
100 Watts CONTROLLING Fixture
Maximum Lamp Wattage...
User Guide - Page 4
... and void your warranty. Note: Sensor has a 1 1/2 minute warm up period before installing
cover. 5.
White to White Black to Black
Black to Red and Black
Red to Black
Ground to Ground
Motion Sensing Light
Controlled Motion Sensing Light
Wiring Motion Sensing Light to Control Another Motion Sensing Light
It is also possible to wire two motion sensing lights so that only people with...
User Guide - Page 5
...motion across the
coverage area. Also, the tip of cut foam tape and adhere lens shield to sensor lens. Note: To help determine amount of lens shield required, apply small sections one side...this light fixture detects "motion"
by 30 degrees. Bulb Type Candelabra Base, Type "B", 25 Watt Maximum Sensor Capacity Up to 25 Watt Maximum each section may be installed.
The sensor ...
User Guide - Page 6
... not 1. come on 1. Daylight turn-off is set too high.(Reduce
sensitivity.)
Light flashes on
for no apparent animals or automobile traffic. Incorrect circuit wiring, if this is a heat source like an
continuously.
Light comes on .
2. Sensor may be installed in a
in daylight.
air vent, dryer vent, or brightly-
Bulbs are loose or burned...
User Guide - Page 7
... for inconvenience, installation, setup time, loss of incidental or consequential damages, so the above limitation or exclusion may also write* to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by factory defective parts or workmanship will void this Product
FIVE YEAR LIMITED WARRANTY This is...
Similar Questions
Any Way To Purchase Just The Lens To Replace A Shattered One?
Hi - lens fell out on Model SL - 5525 and shattered on driveway below. Is there any way to purchase ...
Hi - lens fell out on Model SL - 5525 and shattered on driveway below. Is there any way to purchase ...
(Posted by gregellie 2 years ago)
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Zenith Sl-6040-wh-b Configurations
Where can I find more information? Such as number of sensors that can be used
Where can I find more information? Such as number of sensors that can be used
(Posted by johannesgrande 12 years ago)
Using Two Sl 6106 Wh Switches
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
(Posted by mrnester 13 years ago)
