Yamaha HS80M Support Question

Find answers below for this question about Yamaha HS80M - HS 80M Speaker.
Need a Yamaha HS80M manual? We have 1 online manual for this item!

Yamaha Overview Questions Manuals Reviews Videos Research

Question posted by stevebest2 on May 31st, 2010

Does The Speaker Have An Internal Fuse?

my tweeter isn't working

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Yamaha HS80M Manual Pages

Owner's Manual - Page 4

... any distortion or unnatural color shift. Connections • Before connecting the device to the internal components. • Do not place the device in this can result in every locale,... and have the device inspected by qualiﬁed Yamaha service personnel. • If this speaker system (HS50M, HS80M only) is a sudden loss of sound during use the voltage speciﬁed as follows ...

Owner's Manual - Page 5

...the retouched photo, but in most other line-level connections in the kitchen. HS80M/HS50M/HS10W Owner's Manual 5 English Setting Up for Superior Monitor Sound Unlike ...sabotage your sound on the tradition with the shortest possible unbalanced cables. The HS-series monitors carry on other systems. The legendary Yamaha NS10M became a standard...speakers are located on top of your Yamaha...

Owner's Manual - Page 6

....) The phone jacks will usually be used in a production type setup. MG Series 6 HS80M/HS50M/HS10W Owner's Manual English XLR-type Connector (Balanced) This is simple enough: use with...Signal + or "Hot" Sleeve: Ground RCA Pin Jack The HS-series studio monitors also feature 1/4-inch phone jack connectors that can be feeding your HS speakers directly to a mixer such as one of the Yamaha MG-...

Owner's Manual - Page 7

...is one of your speakers get to walls and corners the more than 1.5 meters (5 feet) away from the side and rear walls. English The HS-series speakers are formidable. As ... mentally or use some compensation - HS80M speakers make the most accurate response your electronic keyboard or other is all too often overlooked with a speaker's frequency characteristics. Just keep in the...

Owner's Manual - Page 8

... so that may be one apex of the speakers should be such that the tweeters are roughly aligned with your ears (this setup..., set the LOW CUT switch to "FLAT". ● When set to "-2 dB" to attenuate the highs slightly if you ﬁnd the sound too bright. 8 HS80M/HS50M/HS10W Owner's Manual Fine-tuning for Stereo ● The speaker...

Owner's Manual - Page 9

.... For accurate monitoring, however, set the MID switch to "0". ● Set the HS50M/HS80M ROOM CONTROL switch according to the distance your subwoofer is a total of your speakers are positioned in - two main speakers plus one center speaker plus two rear speakers is not as critical as required. The extended bass response provided by a good...

Owner's Manual - Page 10

... - C L R LFE OMNI Out LS RS 10 HS80M/HS50M/HS10W Owner's Manual each of string cut or marked to the speaker position the string will be connected directly to the console output... that is to use it will also provide a convenient guide for surround production, your HS-series speakers to handling that they point directly at the listening position. In this type of a ...

Owner's Manual - Page 11

... to the distance your ears. This is obviously bad for your music as well as your speakers are probably starting to check if any elements of your mix at different levels as required. ...relative balance with the subwoofer. * If you 're using the HS50M with the HS50M or HS80M speakers. * Set to maintain a consistent monitoring level otherwise you should stay within a fairly small ...

Owner's Manual - Page 12

... +2dB 0 -2dB FLAT 80Hz 100Hz POWER ON " # $ % & ' ! 1 POWER switch Turns power to the speaker on the front panel will light. When the power is boosted by -2 dB. ' LOW CUT switch Cuts the low-frequency ...type connector at frequency response. Setting the switch to the speaker, then insert the power cord plug into the AC outlet. 12 HS80M/HS50M/HS10W Owner's Manual With the "+2 dB" setting, ...

Owner's Manual - Page 13

...speaker on . ' HIGH CUT control Use the HIGH CUT control to set the cutoff frequency from 80 Hz to 120 Hz. ( LEVEL control Adjusts the overall output level. ) PHASE switch Selects a phase of these INPUT connectors. If two signals are input at the same time. However, the "REV." HS80M...switch is on , the low frequencies of the entire speaker system. First connect the power cord to add a ...

Owner's Manual - Page 14

...HF) : ROOM CONTROL (0/-2/-4 dB under 500Hz) Indicator Power Consumption Power ON : White LED 45W HS80M HS10W Biamp 2-way Powered speaker 2 kHz 42 Hz-20 kHz (-10 dB) 250 x 390 x 332 mm (9-13/16 ...20 kHz (-10 dB) 165 x 268 x 222 mm (6-1/2 x 10-9/16 x 8-3/4") 5.8 kg Speaker Components Speaker Components Enclosure Type Material LF : 5" cone (Magnetic shielding Type) HF : 0.75" Dome (Magnetic ...

Owner's Manual - Page 15

...: mm(inch) Performance graph RESPONSE (dB) HS50M +10 0 -10 -20 -30 -40 20 100 1k 10k FREQUENCY (Hz) Block Diagram RESPONSE (dB) HS80M +10 0 -10 -20 -30 -40 20 100 1k 10k FREQUENCY (Hz) RESPONSE (dB) HS10W +10 0 -10 -20 -30 -40 20 100... OUTPUT EXTSUB OUT LOW CUT ON/OFF SUM LOW CUT LF LOW CUT HIGH CUT PHASE P.AMP SPEAKER NORMAL REVERSE LIMITTER LEVEL 67