Whirlpool WTW7600XW Support Question
Find answers below for this question about Whirlpool WTW7600XW.Need a Whirlpool WTW7600XW manual? We have 5 online manuals for this item!
Question posted by rgray6 on December 11th, 2011
What Does F-50 Mean
Current Answers
Answer #1: Posted by Odin on December 11th, 2011 12:58 PM
Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine cause of friction.
If basket turns freely:
Drain water from tub and:
1. See Activation of Manual Diagnostic Test Mode, and check the motor and electrical connections by performing the Agitate and Spin tests under Manual: Motor. The following steps assumes that this stepfailed.
2. Unplug washer or disconnect power.
3. Check to see if basket will turn freely. If basket turns freely, go to step 4. If basket does not turn freely, determine what is causing the mechanical
friction or lock up.
4. Remove the console to access the machine/ motor control assembly. See Accessing& Removing the Electronic Assemblies.
5. Visually check that the P5 and P10 connectors are inserted all the way into the machine/motor control. If visual checks pass, go to step 6.
If visual checks fail, reconnect P5 and P10 and repeat step 1.
6. With an ohmmeter, check for 16 ohms resistance at the P5 connector between pins P5-1 and P5-2, and also between pins P5-1 and P5-3. Also measure the resistance at the P10 connector between pins P10-1 and P10-7 and verify that the resistance is within the range shown in the wiring diagram on page 7-1.
If the resistance is correct, go to step 11. If the P5 connector resistance is much higher than 16 ohms, or the P10 connector resistance is out of range, go to
step 7.
7. Tilt machine forward to access the bottom of the machine and the drive motor area. See Figure 1 on page 6-13. Remove the motor bolt, then the motor cover to access the motor connections. See Figure 2 on page 6-13.
8. Visually check the mounting bracket and electrical connections to the motor and rotor position sensor board. If visual check passes, go to step 9.
If visual check fails, reconnect the electrical connections, reassemble stator and motor cover and repeat step 1.
9. With an ohmmeter, check for continuity between all pins on the P10 machine/motor control connector and the motor rotor position sensor (RPS) connector. See Figures 2 and 4, pages 6-13 and 6-16. If there is continuity, go to step 11. If there is no continuity, replace the lower machine harness.
10. With an ohmmeter, check for continuity between all pins on the P5 machine/motor control connector and the drive motor connector. If there is continuity, replace the drive motor. If there is no continuity, replace the lower machine harness.
11. The drive motor and lower harness are good. Replace the motor RPS board and perform the Diagnostics test in step 1 to verify repair.
12. If the Diagnostics motor test in step 1 failed, then the machine/motor control has failed: Unplug the washer or disconnect power. Replace the machine/motor control assembly. Perform the Motor Diagnostics in step 1 to verify repair.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool WTW7600XW Manual Pages
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How does my 50-lb. undercounter ice maker work?
...maker shuts off automatically and restarts when more ice is drained after reach freezing cycle. This means that higher operating temperatures result in the water are rejected. My ice maker runs but ... slides onto a cutter grid. This produces a sheet of ice produced and stored. How does my 50-lb. undercounter ice maker work ? How does my ice maker work ? When the desired thickness is... -
Why is HE High Efficiency detergent the only type of detergent to use in my washer?
This means only a small amount is needed for the content of this site. Look for the HE symbol on the ...suds. Error codes. Whirlpool does not endorse and is specially formulated to excess suds hindering spinning and draining. FAQs Knowledgebase search tips Washer not draining, not spinning out water; With less water, the wash action can create too much sudsing when regular detergent is not... -
How do I clean my Cabrio® top-loading washer?
...: These instructions are for liquid fabric softener only. IMPORTANT: Be sure the inner cone-shaped cup is not cleaning laundry - Washer has an odor - For cleaning information regarding the Cabrio top-loading washer with 6th Sense TM Technology, click here Cleaning the interior Cleaning the liquid fabric softener dispenser Cleaning the exterior Clean...
Similar Questions
Washer over flowing on certain settings and flossing bathroom
How many cubic feet in the whirpool Cabrio WTW7600XW in the washing machine?
Whirlpool Cabrio, Model:WTW7600XW0