Whirlpool WTW5600XW Support Question
Whirlpool WTW5600XW Support Question
Find answers below for this question about Whirlpool WTW5600XW.Need a Whirlpool WTW5600XW manual? We have 5 online manuals for this item!
Question posted by Aries67 on September 8th, 2014
Won't Finish A Cycle
No matter what setting I have my washer on, the washer stops without completing the final spin. The water is out of the basket but the clothes are wet. I have to unplug the washer then plug it in and put it on the drain and spin cycle to spin the clothes. I did the diagnostics and it said F0 E5
Current Answers
Answer #1: Posted by Odin on September 8th, 2014 10:24 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,740
Member since:
April 10th, 2010 Points: 41,236,740
Related Whirlpool WTW5600XW Manual Pages
Owners Manual - Page 3
... amount of humming and whirring sounds as the washer determines the correct water level for clothes to thoroughly wet the load. Normal Sounds You Can Expect
At different stages of the clothes will hear the motor turn the basket in the "Cycle Status Lights" section. The washer automatically adjusts the water level to the soils.
WHAT'S NEW UNDER THE...
Owners Manual - Page 4
Using the EcoBoost setting on a cycle can be used with all options can also be added to the washer to increase your energy savings on your fabric.
• Warm and hot water will help reduce tangling and wrinkling.
4
SPIN SPEED This washer automatically selects the spin speed based on the cycle selected. SOIL LEVEL Soil level (wash time) is...
Owners Manual - Page 5
... that the lid is complete. WASH
You will unlock once the washer movement has stopped. At each stage of the process, you may repeat until the correct amount of water has been added for best results.
These sensing spins may take several minutes if the load was selected. Factors such as cycle is locked and cannot...
Owners Manual - Page 6
... detergent
Hand-washed items or dripping wet items
No clothes in washer
Rinse & Spin
Drain & Spin
Clean Washer
with enough water to drain washer after cancelling a cycle or completing a cycle after power interruption. This cycle uses a spin to complete a load after a power failure. Use this cycle to wet down the load before washing.
CYCLE GUIDE
Settings and options shown in bold are...
Owners Manual - Page 7
..., buttons, or any small object can set stains into washer
• Empty pockets.
Separate lint-takers from sturdy fabrics.
• Do not dry garments if stains remain after washing, because heat can pass under the washplate and become trapped, causing unexpected sounds.
• Sort items by recommended cycle, water temperature, and colorfastness.
• Separate...
Owners Manual - Page 8
...-water washing creates excessive sudsing with liquid chlorine bleach. It may cause detergent to ensure proper distribution at the end of the washer basket before adding clothes.
Using Oxi or color-safe bleach: If using an Oxi or color-safe bleach laundry boost product, add to dispenser
Detergent tray
5. If Extra Rinse option is closed completely...
Owners Manual - Page 9
... your previous washer provided. Indicator for that bleed or fade Light soils
Cold Warm water may be lit. Press DELAY WASH button to set a delayed Start: 1.
brights/darks Warm water is lined up with a cycle, you may absorb moisture from your faucet.
The delay countdown has started when the START/Pause/Unlock light stops blinking.
This...
Owners Manual - Page 10
...
Select any spills.
2. P ress START/Pause/Unlock to
begin wash cycle
WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after cycle has completed to avoid odor, reduce wrinkling, and rusting of the spin prior to add, if not previously set ). CLEANING YOUR WASHER
Keep your washer as clean and fresh as Deep Clean or Extra Rinse. Using recommended AFFRESH...
Owners Manual - Page 11
... packing tray from drain system and drain any remaining water into basket opening. Close lid and place tape over edge and into slot. Because some water may find laundry product residue leftover in washer or reconnect power. 3. Shut off both water faucets. disconnect and drain water
inlet hoses. 2.
Flush water pipes and hoses. Turn on RINSE AND SPIN cycle for about 30 seconds...
Owners Manual - Page 12
... not be draining water. If you have started the washer. Load could unbalance washer. For normal operating sounds, go to the washer. Loose items such as expected
Not enough water in washer
Load not completely covered in water. Water Leaks
Check the following for oversized, non-absorbent items such as final amounts of alignment and cause water to drainpipe or laundry tub.
Check...
Owners Manual - Page 13
... hum of cycle. You may be stopped to possibly avoid a service call. Always measure detergent and follow detergent directions based on (indicating that the washer was unable to fill appropriately)
Check for assistance and to reduce suds. Plug power cord into a grounded 3 prong outlet. Replace any kinks in basket and add detergent. Select RINSE & SPIN. If...
Owners Manual - Page 14
... recommended.
Check plumbing for the fabrics being washed. Cycles with air flow during the final spin. Use the recommended cycle/speed spin for loading recommendations. Load may be attached and have both hot and cold water flowing to the inlet valve.
See "Using Your Washer" for your load.
Lower drain hose if the end is tightly packed. Always...
Owners Manual - Page 15
... dispensers to possibly avoid a service call.
See the Cycle Guide to move. Not cleaning or removing stains
Wash load not completely covered in dispenser after washing detergent or bleach residues
may require additional rinsing.
Washer senses load size and adds correct amount of water still in water. Load garments in less effective cleaning. Not using...
Owners Manual - Page 16
... load.
Button sounds can occur in pockets during wash cycle.
Do not overfill dispenser, which causes immediate dispensing. Sharp items were in a tightly packed load. No sound when buttons are pressed
Button sounds are detected, the washer will not unlock until the basket has stopped spinning. Be sure to break down suds. If excess suds...
Dimension Guide - Page 1
... doors, and floor moldings. Consider allowing more than 96" (2.44 m) from bottom of washer.
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). install no higher than 4.5" (113 mm)...) from bottom of washer. Dimensions are required. For complete details, see Installation Instructions packed with spacing of the door are for floor standpipe drain system. Specifications subject to...
Installation Instructions - Page 2
... Number 285835
Lint clogged drain
Drain Protector Part Number 367031 Connector Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or ...
Drain hose with clamp
Inlet hoses with flat washers
To order, please refer to toll-free phone numbers on back page of your washer in the top of your washer ...
Installation Instructions - Page 3
..." in temperatures below the top of drain hose should be exposed to reduce noise transfer. Minimum carry-away capacity: 17 gal. (64 L) per minute. install no more space for ease of 1" (25 mm) under entire washer. If you need :
n A water heater set to 120° F (49° C). This washer has been tested for closet door...
Installation Instructions - Page 5
...in standpipe
Drain hose form
Firmly grasp power cord plug and pull to move washer later.
4.
Drain hose form must be inside standpipe; Attach drain hose to back of washer.
4.5" (...of drain hose onto black drain port and secure with separate directions.
IMPORTANT: 4.5" (113 mm) of laundry tub. For a laundry tub or standpipe drain, go to remove all parts from tub
Connect Drain ...
Installation Instructions - Page 6
... overtighten or use tape or sealants on washer. Check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to tighten couplings an additional two-thirds turn . Remove drain hose form (floor drain installations only)
9. Connect Inlet Hoses
Washer must use old hoses.
Attach hot water hose to water faucets with new inlet hoses with a red...
Installation Instructions - Page 8
... or liquid detergent and pour it into washer basket or detergent dispenser (on some models). Start washer and allow to see what was skipped.
q Check that yellow shipping materials were completely
removed from console and any cycle. q Dispose of your tools. q To test and clean your Washer User Instructions. Plug into a grounded 3 prong outlet. q Check for leaks...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Washer is not cleaning laundry - Top-load washer
... need to 250 mL) warm water. Agitator is not cleaning laundry. Top-load washer Lint is on some models): Use only liquid fabric softener in water? Top-load washer Not draining, not spinning out water, wet loads - Top-load washer My top-load washer is loose - Sort loads before starting the washer. Are the hot and cold water inlet hoses reversed? See the... -
The amount of water seems too low - Top-load HE washer with Dispenser Drawer - video
... more water will unlock briefly before water is not completely submerged in Corners There is not cleaning laundry - Next, the washer will first perform a self-test on the lid lock. Top-load HE washer with Dispenser Drawers - The washer senses the size of the load and adds the correct amount of water for the clothes to... -
Dry fabric after washing - Top-load HE washer with Dispenser Drawer
... the top of the laundry dry after the cycle completes? Vibration - This is normal and is more likely to happen with Dispenser Drawer - Top-load HE washer with Dispensers in Corners Washer will not fill or start - washer with Dispenser Drawer - Top-load HE washer with Dispenser Drawer Dry fabric after the final spin. The load has...
Similar Questions
How Is The Noise Of Short Agitator On Whirlpool He Washer Model # Wtw5600xw
(Posted by timotwch 9 years ago)
Top-loader Wtw4950xw2 Won't Finish Cycle And Won't Restart
This weekend, the washer stopped during the spin cycle. Tried unplugging and resetting. Only thing i...
This weekend, the washer stopped during the spin cycle. Tried unplugging and resetting. Only thing i...
(Posted by jeffreyiannazzo 10 years ago)
Spin Cycle Does Not Work Properly
after the spin cycle complete i have to do 2 more spin cycles to rid water from clothes why is that?
after the spin cycle complete i have to do 2 more spin cycles to rid water from clothes why is that?
(Posted by mgbs045 11 years ago)