Whirlpool WTW5500XW Support Question
Whirlpool WTW5500XW Support Question
Find answers below for this question about Whirlpool WTW5500XW.Need a Whirlpool WTW5500XW manual? We have 5 online manuals for this item!
Question posted by thjankoz on March 14th, 2014
Whirlpool Cabrio Wtw5500xw1 Will Not Cycle
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW5500XW Manual Pages
Dimension Guide - Page 1
...least 39" (990 mm) above floor; Floor drain system requires additional parts.
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to...(710 mm) from bottom of laundry tub must install higher than 4.5" (113 mm) of drain hose should be provided. install no higher than 96" (2.44 m) from bottom of washer. If a closet door or...
Installation Instructions - Page 2
...(51 mm) diameter to improve performance and minimize noise and possible "washer walk". Install your washer to 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector ... Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 ...
Installation Instructions - Page 3
.... Water remaining in your responsibility. Top of laundry tub must be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. ...laundry tub. n A grounded electrical outlet located within 3 ft (0.9 m) of hot
and cold water fill valves on back of 0" (0 mm) clearance on the sides. n A level floor with spacing of washer.
Proper installation is your Use and Care Guide. This washer...
Installation Instructions - Page 5
... force excess hose into standpipe (shown in picture) or over end as shown in case you need additional parts with clamp. For a laundry tub or standpipe drain, go to move washer later.
4. 3. Attach drain hose to free from tub. Free power cord
If clamp is not already in standpipe
Drain hose form...
Installation Instructions - Page 6
...
Connect inlet hoses to water faucets
Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to hot water inlet valve marked with cold water inlet valve. ...Clear water lines
For floor drain installations, you must be attached and have water flowing to washer correctly. Damage can result.
IMPORTANT: Do not overtighten or use old hoses. IMPORTANT: To...
Installation Instructions - Page 7
... standpipe, or inlet hoses for wall standpipe with floor. Secure drain hose
Laundry Tub
Standpipe
Wall
14.
Level Washer
IMPORTANT: Level washer properly to prop washer with a wood block or similar object that will support weight of sides. Check levelness of washer and repeat as needed. HELPFUL TIP: You may want to reduce excess noise...
Installation Instructions - Page 8
... water faucets are now installed.
q To test and clean your Washer User Instructions. q Check that all of washer. Start washer and allow to see what was skipped. q Check that yellow shipping materials were completely
removed from console and any cycle. q Read "Washer Use" in your washer, measure 1/2 of normal
recommended amount of /recycle all packaging materials...
Owners Manual - Page 3
... to the soils. Low-water washing creates excessive sudsing with dirty laundry, fill it evenly around the basket wall. Follow the manufacturer's instructions to determine the amount of the wash cycle, you start the cycle, the lid will lock, and the washer will hear the motor turn the basket in component failures and noticeable...
Owners Manual - Page 4
...restarted. The wash time is preset for your laundry load. CONTROL PANEL AND FEATURES
1
2
4
5
3
1 WASH CYCLE KNOB Use the Wash Cycle knob to select available cycles on briefly (short hum) to move the ... working properly. These sensing spins may be cooler than diluting detergent as the washer rinses and moves the load. The sensing light may change at the correct time in...
Owners Manual - Page 5
... Drain & Spin, add additional detergent and select a cycle based on selected cycle and spin speed.
This cycle features a spray rinse. Use this cycle is used, the wash cycle will not spin. The Eco Normal cycle allows you need to drain washer after cancelling a cycle or completing a cycle after power interruption.
SPIN
The washer spins the load at high speed. If...
Owners Manual - Page 6
...using the Bulky Items cycle.
• Use mesh garment bags to help avoid tangling when washing delicate or small items.
• Turn knits inside out to your laundry
2. Synthetics, knits... because heat can set stains into washer
• Empty pockets.
Try mixing different sized items to reduce wrinkling and tangling.
6 USING YOUR WASHER
1. Load garments in loose piles around the ...
Owners Manual - Page 7
... creates excessive sudsing with liquid chlorine bleach.
Do not overfill or dilute. Starting Your Washer
6. Select cycle
Turn cycle knob to turn on your wash cycle. Using Oxi or color-safe bleach: If using an Oxi or color-safe bleach laundry boost product, add to be marked "HE" or "High Efficiency." adding too much detergent...
Owners Manual - Page 8
... Level, and Spin Speed, if desired. Filling is left open the lid to start the wash cycle. If lid is delayed for that bleed or fade Light soils
Press the START/PAUSE/UNLOCK button...to filling. the lid will automatically add certain options such as Extra Rinse. Some cycles will unlock once the washer movement has stopped. NOTE: Always read and follow fabric care label instructions to ...
Owners Manual - Page 9
... water may find laundry product residue in warm, soapy water, using liquid chlorine bleach, add 1 cup (250 mL) to reduce the risk of hose failure.
To remove residue, follow this recommended cleaning procedure: 1. Air dry, or dry with AFFRESH™ cycle. Press POWER.
5. Use all-purpose surface cleaner, if needed. WASHER MAINTENANCE
WATER...
Owners Manual - Page 10
... .
3. Place packing tray from back of washer. Keep lid taped until washer is placed in washer or reconnect power. 3.
Before using again, run washer through BULKY ITEMS cycle to locate, level, and
connect washer. 2. TRANSPORTING YOUR WASHER
1. Place inlet hoses and drain hose inside washer. Refer to Installation Instructions to clean
washer and remove antifreeze, if used. Turn on...
Owners Manual - Page 11
...four fill hose flat washers are removed during the spin/drain cycles. See "What's New under your washer will not be unbalanced.
Make sure all household plumbing for leaks (laundry tubs, drain pipe...clogged sink or drainpipe. Pull drain hose from washer cabinet and properly secure it to washer. For normal operating sounds, go to www.whirlpool.com/help for service to remove items.
It...
Owners Manual - Page 12
... at www.whirlpool.com/help for assistance and to reduce suds.
Replace any kinks in basket. Washer will pause during certain phases of the spins. The washer senses the dry.../PAUSE/UNLOCK. Lid must be closed for washer to 3 minutes before the water is normal.
Select RINSE & SPIN.
Normal washer operation. To remove suds, cancel cycle.
NOTE: If problems continue, contact an ...
Owners Manual - Page 13
... with a low spin speed.
Both hot and cold water faucets must be on load after washer has started.
13
The washer is less efficient at www.whirlpool.com/help for correct drain
hose installation. Add only 1 or 2 garments after cycle
Incorrect or wrong wash or rinse temperatures
High speed spins extract more moisture than...
Owners Manual - Page 14
... garments in dispenser.
14
Added water lifts the laundry off the washplate, resulting in water. Washer is less efficient at www.whirlpool.com/help for the type of water.
Always ...cycle is complete to match your load with the best cycle.
Use a higher soil level cycle option and warmer wash temperature to washer. Use Whites and Heavy Duty cycle for clothes to the selected cycle....
Owners Manual - Page 15
... spills.
See the "Cycle Guide" to remove.
Run the Clean Washer cycle with the best cycle.
Always follow garment manufacturer's care label instructions.
The washer may take several minutes...Incorrect dispenser operation
Clogged dispensers or laundry products dispensing too soon. Be sure to assure proper dispensing.
Items may be turned on your Washer" section. Always read and ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How do I clean my Cabrio® top-loading washer?
... the base. IMPORTANT: Be sure the inner cone-shaped cup is not cleaning laundry - Washer is straight and placed completely in the top of detergent. Remove any spills. ...Cabrio® How do I clean my top-loading super- Use a soft, damp cloth or sponge to keep it through a complete cycle using only cleaners labeled as washer safe. Top-load washer Purchasing Affresh washer... -
How do I clean my top-loading super- or large-capacity washer?
..., click To avoid damage to keep it through a complete cycle. Do not add detergent or bleach to the washer, select a hot wash, and run it looking new. Use...on cleaning the Cabrio TM top-loading washer, click Rinse dispenser under warm water, and then replace it is not cleaning laundry - Occasionally wipe the outside of your washer to the washer or clothing, ... -
Lint is on the load - Top-load HE washer with Dispensers in Corners
.... Were you select a high-speed wash action cycle or a long wash time? The load must be trapped in the water. Did you use high-speed wash action and long wash times for the Cabrio HE washer. The residue from the laundry load. Wash water colder than 60°F (15.6°...
Similar Questions
What Causes Whirlpool Cabrio Wtw5500xw1 Cycle Problems
(Posted by silvkj 9 years ago)
How Do I Test The Lid Lock Switch On A Whirlpool Cabrio Wtw5500xw1
(Posted by adbly 10 years ago)
Why Wont My Whirlpool Cabrio(wtw5500xw1) Start Up?
When I first turn on my whirlpool washer and push the power button it just blink and all of the lits...
When I first turn on my whirlpool washer and push the power button it just blink and all of the lits...
(Posted by pamelasims39 10 years ago)
