Whirlpool WGD4890XQ Support Question
Whirlpool WGD4890XQ Support Question
Find answers below for this question about Whirlpool WGD4890XQ.Need a Whirlpool WGD4890XQ manual? We have 4 online manuals for this item!
Question posted by cknox on September 25th, 2011
How Do I Hook Up The Dryer Cord? New Dryer Tumbles But, No Heat. I Notice No
220 line installed. Thanks very much
Current Answers
Related Whirlpool WGD4890XQ Manual Pages
Owners Manual - Page 2
DRYER SAFETY
2
Owners Manual - Page 4
... covered by the warranty and will be sure to follow the "Installation Instructions" supplied with heat, dryers require good air flow to over-drying. The Energy Preferred cycle ...elbows in shrinkage, wrinkling, and static due to efficiently dry laundry.
Good
Better
n Remove lint and debris from the front the dryer. Proper venting will provide optimal energy savings. n Replace ...
Owners Manual - Page 5
...; setting ends.
5 n Get up to start the dryer. Press the PUSH to START knob to 40 minutes of heat-free, periodic tumbling at the end of Cycle Signal is not available on ...minutes until the clothes are available on your laundry load. NOTE: The Air Only temperature setting (on some models)
When you are unable to select for your dryer.
Appearance may choose a setting based on...
Owners Manual - Page 6
... shortest time.
Setting the Drying Temperature
If your load.
Line dry bonded or laminated fabrics. NOTE: If you are... load
Heavy Dry Damp Dry
Any load
Tumble Press®
Rubber, plastic, heat sensitive fabrics
Fluff Air
Temperature: Any Any...suitcase or in items wrinkled from being left in your dryer has multiple heat settings:
A High heavy temperature setting may be used for...
Owners Manual - Page 7
.... Roll lint off the screen with your dryer, wipe the dryer drum with a damp cloth to remove lint. Place laundry in the dryer. Clean the lint screen
2. Do not ... electric shock, or injury to tumble freely.
7 For additional cleaning information, see "Dryer Care". Load the dryer
Clean the lint screen before operating this dryer.
USING YOUR DRYER
WARNING: To reduce the risk ...
Owners Manual - Page 8
....
Wrinkle Shield™ feature (on some models)
n Get up to 40 minutes of heat-free, periodic tumbling at which the dryer will sound every 5 minutes until the clothes are removed, or the Wrinkle Shield™... the desired cycle
TIMED DRY 50
40
Damp Dry
Tumble Press
20
60
70
Heavy Dry
Cool Down
OFF ACCUDRY sensor dryer Jeans Very Dry
ENERGY PREFERRED
OFF
Delicate
WP_WEGD4900XW
Less ...
Owners Manual - Page 9
... years, or more often, depending on the lint screen. This includes clearing piles of laundry in the dryer. Apply a liquid, nonflammable household cleaner to dry the drum. Cleaning the lint screen
...screen is removed. 2. Do not rinse or wash screen to a residue buildup. Tumble a load of the dryer. From the Exhaust Vent Lint should be removed every 2 years, or more frequently,...
Owners Manual - Page 10
... base. 4. Make sure leveling legs are at fuse or breaker box. 2. Disconnect gas supply line pipe and remove fittings
attached to dryer. 2. Unplug dryer or disconnect power.
2. For direct-wired dryers: 1. Disconnect wiring. 3. Reinstalling the Dryer
Follow the "Installation Instructions" to secure dryer door. See "Cleaning the Lint Screen." Use tape to locate, level, and connect the...
Owners Manual - Page 11
... closed completely.
Replace both fuses or reset the circuit breaker. Electric dryers require 240-volt power supply. No heat
Are the four legs installed, and is the dryer level front to back and side to tumble freely. Supply line valve not open on the supply line. Incorrect power supply.
Replace both fuses or reset the circuit breaker...
Owners Manual - Page 12
...the cycle.
If so, ventilate the area. Were laundry items removed from the dryer before Cool Down may have an odor. The new electric heating element may feel very warm. Items removed before ...wrinkling and make it easier to avoid wrinkling. Select Wrinkle Shield™ feature to tumble the load without heat to handle. When the odors or fumes are wrinkled
Load not removed from the area...
Dimension Guide - Page 1
...Dryer can result. When rigid pipe is used it should be in accordance with equivalent air ventilation openings are for 27" have a 90° turn to change materials and specifications without notice. Pipejoint compounds resistant to L.P. An individual manual shutoff valve must be installed... that will help to the cold water faucet using new inlet hoses. Do not use vent runs longer than...
Installation Instructions - Page 2
... with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1. This symbol alerts you to reduce the chance of injury, and tell you...the safety alert symbol and either the word "DANGER" or "WARNING."
DRYER SAFETY
Your safety and the safety of others . The dryer must conform with local codes, or in this manual and on your ...
Installation Instructions - Page 4
... or storing your old clothes dryer, remove the door.
Tools needed for all installations:
Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench
Caulking gun and compound (for installing new exhaust vent)
Flat-blade screwdriver
#2 Phillips screwdriver
1/4" nut driver or socket wrench (recommended)
Tin snips (new vent installations)
Utility knife Tools needed for...
Installation Instructions - Page 5
Contact your local building inspector. If not level, clothes may not tumble properly and automatic sensor cycles may not operate correctly. The dryer must not be installed or stored in an area where it will need: ■■ A location allowing for proper exhaust installation. Contact your local building inspector. Parts supplied:
Leveling legs (4) Parts package...
Installation Instructions - Page 6
...) or the Canadian Manufactured Home Standard CAN/CSA-Z240 MH.
■■ Metal exhaust system hardware, available for purchase. Most installations require a minimum 5½" (140 mm) clearance behind the dryer for mobile home installations. Recessed area B. For further information, please reference the "Assistance or Service" section of the door are acceptable.
■■...
Installation Instructions - Page 7
.... ■■ To be plugged into a grounded 4 prong outlet. Be sure wall receptacle is properly installed and grounded in conformance with a CSA International Certified Power Cord intended to move and install dryer. This dryer is equipped with the Canadian Electrical Code, C22.1-latest edition and all local codes and ordinances.
If using a replacement power supply...
Installation Instructions - Page 8
... plate for use a wrench to the gas supply. GAS DRYER POWER HOOKUP
Gas Supply Requirements
WARNING
Explosion Hazard Use a new CSA International approved gas supply line. Examples of the "Dryer User Instructions." No attempt shall be installed in the door well of connection.
8 IMPORTANT: The gas installation must be made by which your home. In Canada...
Installation Instructions - Page 9
...65533; For a grounded, cord-connected dryer: This dryer must be provided. WARNING: Improper connection of electric shock. Do not modify the plug provided with a cord having an equipmentgrounding conductor and...installed by providing a path of least resistance for electric current. Check with all local codes and ordinances. If the total length of your dryer to the rigid gas supply line. Dryer...
Installation Instructions - Page 13
... 3/8" pipe elbow D. 3/8" pipe-to-flare adapter fitting
A combination of E.I.
Move dryer to exhaust outlet in dryer. valve is open when handle is parallel to dryer location using straightest path possible. Correct any leaks found. Connect Vent
1. If flexible metal tubing is in supply line; Dupont De Nemours and Company. Avoid crushing or kinking vent...
Installation Instructions - Page 14
..., open .
■■ If the gas supply line shutoff valve is closed .
This odor is common when the heating element is level. If dryer is the 29" Super Wide Side-Swing Door, follow steps 1-6. q Check that all four legs are now installed. q Dispose of/recycle all of dryer from front to see what was skipped...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Vibration - Cabrio® washer
...-load washer. These sounds are normal for details. Vibration that you can contribute to the Installation Instructions for oversized, nonabsorbent items such as the basket tries to extract more water from across... of ¾" (19.1 mm) plywood to the floor beneath the washer and dryer. Refer to washer noise and vibration. The noise and vibration may sound different in different... -
Damp loads or long drying times - Dryer
...;Clean the lint screen before drying every load. Electric dryer Or Dryer does not heat - Make sure that is too large for the dryer will not tumble and limits air movement in the dryer. This slows the process of removing moist air out of this a new installation? The exhaust vent system may be in a room... -
Vibration - Top-load HE washer with Dispenser Drawer - sound clips
...across the room? Do you can feel the vibration across the room can contribute to the Installation Instructions for this cycle. Is the washer basket moving during wash - Normal sound ... a piece of ¾" (19.1 mm) plywood to the floor beneath the washer and dryer. Refer to washer noise and vibration. The noise and vibration may sound different in different...
Similar Questions
Whirlpool Cabrio Model Wed6400sw1 Dryer Wont Heat Up
(Posted by Neilrnirodm 10 years ago)
Wgd6200sw2 Whirlpool Dryer No Heat,
i have whirlpool wgd6200sw2 dryer, with no heat, i checked the back of dryer with Ohm meter, all ok,...
i have whirlpool wgd6200sw2 dryer, with no heat, i checked the back of dryer with Ohm meter, all ok,...
(Posted by chicago164534 10 years ago)
Lte5243dqa Dryer Not Heating
fairly new machine and dryer not heating, need a part which used to be a thermal fuse on the older m...
fairly new machine and dryer not heating, need a part which used to be a thermal fuse on the older m...
(Posted by lashadasapartments 11 years ago)
Why Is The Dryer Not Heating
the dryer turns on an works its just not heating up to dry
the dryer turns on an works its just not heating up to dry
(Posted by michaelmontemayor48 11 years ago)