Whirlpool WFW95HEXL Support Question
Whirlpool WFW95HEXL Support Question
Find answers below for this question about Whirlpool WFW95HEXL.Need a Whirlpool WFW95HEXL manual? We have 5 online manuals for this item!
Question posted by labadiethomas on March 5th, 2013
My Washer Does Not Hold Water.
I have a Whirl Pool Heavy Duty Super Capacity washer with the part number 3358748. As it fills with water it drains from the proper drain under the washer. Is there some kinda valve switch to fill and drain that ain't working?
Current Answers
Related Whirlpool WFW95HEXL Manual Pages
Dimension Guide - Page 1
...delay fuse or circuit breaker is available (Part Number 280130). Floor standpipe drain system
38" (965 mm)
311/2" (800 mm)
1" (25 mm)
Recessed area or closet installation (washer only):
39" min. (990 mm) ...from bottom of your Washer User Instructions. Drain System Options
Drain system can be needed.)
Laundry tub drain system
41/2" (113 mm)
min.
30" (762 mm)
Minimum capacity: 20 gal. ...
Installation Instructions - Page 2
... short
Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835
Lint clogged drain
Drain Protector Part Number 367031 Connector Kit Part Number 285835
Floor drain system
Siphon Break Kit Part Number 285834 Connector Kit (x2) Part Number 285835 Extension Drain Hose Part Number 285863
Alternative Inlet Hoses:
(may be required for installation are in the washer basket. If...
Installation Instructions - Page 3
... located within 4 ft (1.2 m) of hot and cold water fill valves on back of washer to fully open.
See "Washer Care" in Washer Use and Care Guide for winterizing information.
51" (1295...143 kgs). LOCATION REQUIREMENTS
Proper installation is not recommended. n Floor must be exposed to 120° F (49° C).
Space must support washer's total weight (with water and load) of 1"...
Installation Instructions - Page 4
... standpipe. Top of washer. If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). DRAIN SYSTEM
Drain system can be purchased separately. Select method you have an overhead sewer and need . Floor standpipe drain system
41/2" (113 mm)
Laundry tub drain system
41/2" (113 mm)
min. 30" (762 mm)
Minimum capacity: 20 gal...
Installation Instructions - Page 6
... yellow shipping strap from the cord. For a laundry tub or standpipe drain, go to avoid suspension and structural damage, a certified technician must properly set up washer for relocation.
6 C over top
Loosen bolts with washer parts.
5. Pull bolts and plastic spacers from
washer
6. Discard bolts and spacers.
4.
Connect Drain Hose
7. Squeeze clamp with pliers and slide elbow...
Installation Instructions - Page 7
... other when attached correctly.
11. For optimal performance, hot and cold water must be inside standpipe; Place drain hose in attaching hoses to inlet valves.
See "Alternative Parts".
9. IMPORTANT: Only 4.5" (113 mm) of the drain hose.
Water should be attached and have water flowing to washer correctly. Screw on coupling by hand until clear.
7 IMPORTANT: Do not...
Installation Instructions - Page 8
... standpipe with floor, go to washer
Level Washer
Leveling your washer properly reduces excess noise and vibration.
15. If not level, tip washer and adjust feet up or down as necessary.
Repeat with a red ring. Check for leaks
Remove cardboard from side to check for leaks.
Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses...
Installation Instructions - Page 9
... on . Use 1/2 the manufacturer's recommended amount for leaks around faucets, valves, and inlet hoses. Recheck levelness of washer and that all of your tools. q Check that will support weight of washer. q Check that washer is plugged into a grounded 3 prong outlet
Jam nut
When washer is level and all four feet are about 4" (102 mm) with...
Owners Manual - Page 4
Turn the knob to select a cycle for up to pause it for your washer. Steam models
2
1
3
4
5
8
7
9
C
B
6
D
A HE detergent
B Liquid fabric
A
softener
C Chlorine bleach
D Oxi Dispense
Non-Steam ...Wash Cycle Knob to turn the washer on your laundry load. See "Cycle Guide" for detailed descriptions of cycles.
3 START/PAUSE BUTTON Press and hold to start of the wash ...
Owners Manual - Page 5
... the integrated fan circulates air through reduced hot water usage and maintains cleaning performance by pressing and holding for 3 seconds, then pressing START/PAUSE. Not...washer to turn the washer off . Extra Rinse Activate this feature as well. Press the POWER button to the wash load at the proper time in the cycle. A High Efficiency "HE" detergent compartment This compartment holds...
Owners Manual - Page 8
....
Low-water washing creates excessive sudsing with a regular non-HE detergent. n Always read and follow fabric care labels and laundry product instructions. Place a load of detergent to use more than one bag and fill bags equally. Loose change, buttons, or any small object
can plug pumps and may also result in the washer. n Close...
Owners Manual - Page 9
...Powdered detergent: Slide the selector to be dispensed into the washer too early. IMPORTANT: Use powdered detergent when using the ... may seep out before the wash begins.
9 Add laundry products as described in the dispensers from the previous wash... 3-compartment dispenser
HE detergent compartment
Pour a measured amount of water may remain in steps 3-6. 3. Liquid detergent may seep out...
Owners Manual - Page 13
...This is empty.
2.
Make sure laundry drum is normal. Press POWER.
5.
After the cycle has ended, leave the door open to allow the washer to dry between the tub and ...hold START/PAUSE. If any wash cycle is selected, the washer will continue. Then repeat steps 3-6 to liquid chlorine bleach dispenser. Use a soft, damp cloth or sponge to CLEAN WASHER cycle. Use mild soap and water...
Owners Manual - Page 14
... cloth. Align edges of warm tap water. WASHER MAINTENANCE
CLEANING THE DISPENSER
You may find laundry product residue leftover in your dispenser compartments.
Rinse with guides in warm, soapy water, using 3/4 cup (177 mL)... foreign objects. Refer to check for proper use.
14 Open the washer door and remove any clothing or items from the washer.
2. Inspect the gray colored seal between...
Owners Manual - Page 16
... Item cycle for oversized, non-absorbent items such as coins could be draining water.
Check that the drain hose is properly secured to avoid potential leaks. Check all four fill hose flat washers properly seated? Always measure detergent and follow manufacturer's directions based on your washer will reduce sound. This is normal for flexing or sagging. Check floor...
Owners Manual - Page 17
...
Check that inlet valve screens have water flowing to inlet valve.
NOTE: If problems continue, contact an electrician.
Select RINSE/DRAIN & SPIN. Both Hot and Cold water faucets must be attached and have not become clogged. Check proper electrical supply.
Do not add more water to avoid overloading or unbalancing.
Reset a tripped circuit breaker. Washer will pause...
Owners Manual - Page 18
... recommendations for proper installation. TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help for the fabrics being washed.
Select RINSE/DRAIN & SPIN to drainpipe or tub. Both hoses must be attached to both washer and faucet, and have both hot and cold water flowing to inlet valve. Not...
Owners Manual - Page 19
...Monthly maintenance not done as cycle is complete. See "Cleaning Your Washer" in water. Use only HE detergent. See "Cleaning your Washer" section. Solution
Add load loosely. Use only HE detergent. You... items.
Use Whitest Whites and Heavy Duty cycle for tough cleaning. Unload washer as soon as recommended.
To avoid odors, leave the door open after washer has started. Reduce tangling by ...
Owners Manual - Page 20
... in seams before starting a cycle. Avoid tightly packing the washer.
Do not use powdered or liquid laundry boosters in cold or hard water. Use hot or warm washes if safe for the fabrics... properly. Use more than recommended by hand, if needed.
Homes with dry items only. Items may have been added incorrectly. Load with low water pressure may use more detergent for washing heavy ...
Owners Manual - Page 21
...) appears in the inlet hose. F5E2 (door will not lock) Washer door not locking.
Inlet valve screens on .
Then press START/PAUSE again to clear the code. Make sure the drain hose is overloaded. Remove any kinks in display
Check plumbing for proper water supply.
Washer is not kinked, pinched, or blocked. Make sure that may...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Adjusting the door spring tension prior to installing the dishwasher
... should be adjusted. Door Dropping/Opening Hard: Do you are using heavy duty door springs (Part number 4318050) when adding a heavy custom door panel. Standard Tub Models Dishwasher door hitting countertop Product repair... the dishwasher: With another person holding the dishwasher to prevent it opens by itself , move tensioner to a lower numbered hole and replace screw. -
Lint is on the load - Top-load washer
... tumbling of laundry? Cycles such as low-twist terry cloth towels, will produce more lint in the first few washes. Some loosely constructed fabrics, such as Super Wash or Heavy Duty use enough detergent? Lint can be trapped in the load if items are tightly packed in my top-load washer. Lint... -
Adjusting the door spring tension prior to installing the dishwasher
...spring from the tensioner. Door Dropping/Opening Hard: Do you are using heavy duty door springs (Part number 4318050) when adding a heavy custom door panel. The screw can be put into one of three ... prior to installing the dishwasher: With another person holding the dishwasher to prevent it opens by itself , move tensioner to a lower numbered hole and replace screw. Top freezer To...
Similar Questions
Washer Not Holding Water
My washer will not hold water. It seems as if the drain is not closed off during the fill cycle. Mac...
My washer will not hold water. It seems as if the drain is not closed off during the fill cycle. Mac...
(Posted by bptechandeng 8 years ago)
How Can I Get Information On The Whirlpool Elite Washer And Dryer
(Posted by shawntique1201 10 years ago)
Washer Displaying F2/e5 Error Codes..... Not Working At All
(Posted by Nancybriscoe 10 years ago)
Wfw95hexl Won't Fill With Water , Door Locks And That Is It?
(Posted by Bartonjeff13 11 years ago)