Whirlpool WFW9050XW Support Question
Find answers below for this question about Whirlpool WFW9050XW.Need a Whirlpool WFW9050XW manual? We have 4 online manuals for this item!
Question posted by rick94110 on January 11th, 2013
Four Blue Wires Came Off Connector Of Water Level Switch Of 9050xw00
I don't have any idea how to put them back in.
Supporting Image
You can click the image below to enlargeCurrent Answers
Answer #1: Posted by sjj2 on June 21st, 2018 7:07 PM
I had a similar problem. Two wires were connected and two were not. The pressure switch was not attached to the chassis. I think it hung there for 7 years and the vibrations finally caused two wires to break. You can pull the two parts of the connector apart and insert the wires so that they get "pinched" between the split blades of the connectors. When you put the two parts back together, the blades "nick" the insulation on the wires. You may have to force the wires into the split blades with a screwdriver blade first. My washer now works again.
Related Whirlpool WFW9050XW Manual Pages
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The amount of water seems too low - Front-load Duet washer
...; Approximately 1/2 inch of the top of water seems too low when I use my Duet washer. Front-load Duet washer The amount of the baffle will not fill - Wait for the correct water level: Make sure the washer is not cleaning laundry - Front-load washer Washer will remain above the water level. Front-load Duet washer Display shows an error code - Front-load... -
Washer fills slowly - Front-load Duet washer
... screens. Remove any accumulated film or particles from the screens. Inside the inlet valve are turned on the water. The water level will not operate properly with only one of water. Check that the washer is at the lowest 6 o'clock position. Allow the unit to unlock. Open the door and rotate the inner basket... -
Water level control - Load-sensing Energy Star top-load washer with agitator
... chosen. On average, this washer can save up to 15 gallons of water per load compared to drain - Leaking water - Top-load washer There is using too much water. There is the water level control on my load-sensing Energy Star top-load washer with agitator? Washer continues to fill or continues to a washer without load sensing.  ...
Similar Questions
Pressure Switch Wiring
two blue wires are attached to the connector at the pressure switch. Two additional blue wires near ...
two blue wires are attached to the connector at the pressure switch. Two additional blue wires near ...
(Posted by sjj2 5 years ago)
Water Level
It seems as the washer does not fill with enough water. I have had two people look at it and I even ...
It seems as the washer does not fill with enough water. I have had two people look at it and I even ...
(Posted by pmonica37 10 years ago)
Increase A Water Level For Whirlpool Wtw8200yw0
How to increase a default water settings for all the programs, because is not enogh water and clothe...
How to increase a default water settings for all the programs, because is not enogh water and clothe...
(Posted by ivan1 10 years ago)
Whirlpool Front Load Washer Stalls After Filling Up With Water
I have a whirlpool WFW9050XW , but without an LED display. On diagnosis, It blinks 8 times then one....
I have a whirlpool WFW9050XW , but without an LED display. On diagnosis, It blinks 8 times then one....
(Posted by rick94110 11 years ago)
Water Problem
I have water dripping out of the bottom of the washer door and when it fille to rinse it runs out of...
I have water dripping out of the bottom of the washer door and when it fille to rinse it runs out of...
(Posted by jwkillian40 12 years ago)