Home » Uniden » Electronics Accessories » Uniden QT206

Uniden QT206 Support Question

Find answers below for this question about Uniden QT206.
Need a Uniden QT206 manual? We have 1 online manual for this item!

Uniden Overview Questions Manuals Reviews Videos Research

Question posted by mroberts43432 on June 16th, 2014

I Have A Impulse Qt-206 Depth Finder

The person who posted this question about this Uniden product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Uniden QT206 Manual Pages

English Owners Manual - Page 3

Contents Unpacking 2 Features 2 Installing the QT 206 3 Transducer Wiring 4 Power Cable Wiring 4 Installing The Transducer 5 Transom Mount Transducers 5 Through-the-hull Transducers 8 Low Profile Transducers 9... 17 When to Use More Sensitivity 18 Troubleshooting Guideline 19 Features, Specifications, and availability of Optional Accessories are all subject to change without notice. 1

English Owners Manual - Page 4

... readings are shown as whole numbers up to 199 feet. UNPACKING Your QT-206 Depth Sounder box should contain the following items: • Transducer with a soft glowing lamp designed to help your dealer immediately. FEATURES n Depth Readings - The QT-206 is designed to give depth readings from 2.0 feet to the gauge) • Mounting Bracket and hardware •...

English Owners Manual - Page 5

... the washer on your saw or drill. 5. Thread the nut onto the shaft until the U-shaped bracket is a brass shaft. Then cut out. 3. INSTALLING THE QT-206 1. Check behind the panel for the indicator unit, mark a 2-inch hole to be damaged. Extending out of the back of the instrument is firmly against...

English Owners Manual - Page 6

... to wire it directly to the Ignition Switch so that when the switch is applied. POWER CABLE WIRING Because the QT-206 has no ON/OFF switch, you turn the unit on , the depth sounder immediately starts working. It may be convenient to wire the power cable directly to a power source which will...

English Owners Manual - Page 9

...1987, the operating frequency and part number is 1/16 to achieve optimal performance. 4. The QT-206 operates at 200 kHz. (Incorrect frequency will help you identify the operating frequency of each ... reduces the amount of water.) Coating transducers with the water. Route the cable to the QT-206, being careful not to the cable or is kept in saltwater, especially in reduced performance of...

English Owners Manual - Page 15

...touch. Apply the mixture to determine if your chosen location is void free at this point, the depth sounder should now operate. 2. To remove any air bubbles, slowly rotate in a plastic bag ... bag against the hull, pressing the transducer face against the hull. If this point, the depth sounder should now operate. The hull temperature must be permanently bonded to the hull and hard ...

English Owners Manual - Page 16

... ball bouncing up and down to the bottom and returned back to the transducer. Ultrasonic signals from a transducer will not penetrate air. UNDERSTANDING SONAR All depth sounders emit ultrasonic sound signals from the transducer into the water located under your transducer is not mounted properly and you may help to understand...

English Owners Manual - Page 17

... increments (for example: 10, 12, 14, 16, 18, 20 feet). To set the Shallow Water depth alarm so that the alarm is turned off . 15 When you enter water shallower than your ALARM setting.... disappear after you press either the "UP" or "DOWN" keys, the instrument displays the actual depth reading. This number remains in decreasing value so that it will audibly alert you if you see ...

English Owners Manual - Page 18

...preset. However, after installation for installation imperfections. It is at a deeper depth. For example, if the adjustment is typically an adjustment that affects the first 10 feet of boats...may need to adjust this setting again. 16 Since fiberglass hulls are deeper than the actual depth, you may be the same model. This adjustment fine tunes the installation of your readings...

English Owners Manual - Page 19

... the return echoes. WHEN TO USE LESS SENSITIVITY: SHALLOW READINGS Use less sensitivity when your instrument displays a series of random, shallow readings (3.5', 2.9', 4.1') and the actual depth is made in the display window. Then wait 3 to Perform When looking at a time. If you turn . 17 Turning it all the way down, you...

English Owners Manual - Page 20

... turn at the rear of the instrument), you can cause a "doubling" of the actual depth. Then wait 3 to locate the Sensitivity Control somewhere between both ends of the rotation. This...seconds before making this adjustment, turn the control no more sensitivity when your instrument displays depths that is displayed. Increasing this control too far in the less sensitivity direction, you ...

English Owners Manual - Page 21

... logic circuit failure Return unit to appear and are reading Sensitivity Adjustment the correct depth. TROUBLESHOOTING GUIDELINE Symptom "0.0" is important ting or receiving echoes. It is flashing in ...the therefore not transmit- per the instructions in Unit is defective, depth appears in the display window. needs to be properly in the section on...

English Owners Manual - Page 22

... Transom Mount. Alarm Up/Down terminal face mount "chip". lower in erly at high speeds, types of the bottom reading. that the over the true depth. Transducer may require that it deal of air is flowing may be relocated to either on the It could also require that face of the...