Home » Troy-Bilt » Lawn & Garden » Troy-Bilt Storm Tracker 2690

Troy-Bilt Storm Tracker 2690 Support Question

Find answers below for this question about Troy-Bilt Storm Tracker 2690.
Need a Troy-Bilt Storm Tracker 2690 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-173263 on December 15th, 2022

Ajust The Tenson On Tracks

how to ajust the tenson on the tracks

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on December 15th, 2022 11:57 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,650

1,100
points

See Track Tension at https://www.manualslib.com/manual/484345/Troy-Bilt-Storm-Tracker-2690xp.html?page=17&term=tension&selected=1#manual.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Troy-Bilt Storm Tracker 2690 Manual Pages

Operation Manual - Page 1

... LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-07126 (May 02, 2011) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Storm Tracker 2690XP WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices • Set-Up...

Operation Manual - Page 12

... wear gloves when using the heated grip. Caution: It is automatically turned on the machine and in this manual before changing speeds. Controls and Features Track Lock Lever Drive Control Shift Lever Headlight Chute Assembly Chute Clean Out Tool 4 Chute Directional Control Auger Control Heated Grips Steering Trigger Control Augers Skid...

Operation Manual - Page 13

...on the joy-stick and pivot the joy-stick to the right or to engage the track drive. The chute directional control is located on the left . • To change ...NOTE: Always release the drive control before changing speeds. Section 4 - Operate your machine's drive system. Track Drive Control / Auger Clutch Lock Chute Assembly Snow drawn into the auger housing. Failure to maneuver a ...

Operation Manual - Page 14

... for continuous ground contact. Never use your hands to the mounting clip on the rear of track operation. The chute clean-out tool is used on many gravel driveways to clear snow while ...in the operator's position (behind handles until all moving parts have stopped before unclogging. Track Lock Lever The track lock lever is located on the right side of the snow thrower and is conveniently ...

Operation Manual - Page 15

... grip becomes too hot, turn it and the drive motion will move. Top View Track Lock Lever Packed Snow Normal Snow Transport Figure 5-2 Figure 5-1 15 Squeeze the left steering trigger ...for the snow conditions and a pace you are comfortable with your left hand while you shift the track lock lever into the ON position. Select a speed appropriate for instructions on the rear of the six...

Operation Manual - Page 16

... bolts and hex flange nuts which attach it to the snow thrower. 2. Doing so will hinder the snow thrower's drive system. Refer to Fig. 6-1. NOTE: Tracks removed for clarity Figure 6-1 To remove the shave plate: 1. NOTE: When lubricating the hex shaft, be lubricated at least once a season or after every twenty...

Operation Manual - Page 17

...) cannot be achieved adjust the shift cable as follows (See Fig. 6-6): Bow-Tie Cotter Pin Track Side Plate Flange Lock Nut Figure 6-4 Adjustments Shift Cable If the full range of the shaft. ...Tighten the flange lock nut on the shift cable index bracket. Adjust the track tension as follows: 1. Auger Shaft At least once a season, remove the shear pins from the ...

Operation Manual - Page 18

... cable counterclockwise to provide more slack or clockwise to decrease the slack in a clean, dry area. 4. It should be no slack in the cable. The tracks should not roll freely. 3. The unit should not turn. Store in the cable. 5. Maintenance & Adjustments Chute Directional Control To adjust the chute control rod, proceed...

Operation Manual - Page 19

... auger belt off the engine pulley. Auger Belt NOTE: It is out of the engine by removing the self-tapping screws which secure it. NOTE: Tracks removed for clarity Figure 7-2 5. See Fig. 7-3. Do not attempt to avoid unintended starting. 2. See Fig. 7-2. If changing just one . Remove the plastic belt cover at...

Operation Manual - Page 21

... replace belt in the reverse order. Remove the self-tapping screws from the frame cover underneath the snow thrower. 4. Figure 7-8 5. Drive Belt Drive Pulley NOTE: Tracks removed for clarity Figure 7-7 8. Gear Shaft Friction Wheel Assembly Figure 7-9 Section 7 - See Fig. 7-7. 7.

Operation Manual - Page 26

... www.troybilt.com. c. g. Troy-Bilt shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product. HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal...