Troy-Bilt Mustang 50 Support Question
Troy-Bilt Mustang 50 Support Question
Find answers below for this question about Troy-Bilt Mustang 50.Need a Troy-Bilt Mustang 50 manual? We have 2 online manuals for this item!
Question posted by mob816 on August 10th, 2015
My Mustang Rzt 50 Was Running Fine I Got Off For A Minute ,got Back On And It Wo
I was using my mustang rzt 50 it was running fine. I got off of it for a minute got ck on and it won't start. Controls are in neutral position, I'm on the seat. ,pro is disengaged, when I turn the key the indicator light for parking brake lights up.which is also engaged??????
Current Answers
Answer #1: Posted by Odin on August 10th, 2015 5:58 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
See http://www.repairclinic.com/RepairHelp/Lawn-Mower-Repair/21---Unp0IDUw/Lawn-Mower-Troubleshooting. The links most likely to solve are those listed 1st, 2nd, and 9th.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Mustang 50 Manual Pages
Operation Manual - Page 4
.... Uneven terrain could result in . Avoid starting or stopping on steep slopes. Check overhead clearances carefully before attempting to improve stability. to the 'ON' position and move the RH and LH drive control
levers to the neutral position before driving under the influence of the machine. Do not use the slope gauge included as
18. Reduced...
Operation Manual - Page 5
... opening at least five minutes before refueling. Do not shift to another area.
To avoid personal injury or property damage use a nozzle lock-open flame, spark or pilot light as described later in this machine. Use only an approved gasoline container. Always place containers on yourself or your vision of control.
5.
When practical, remove gas...
Operation Manual - Page 12
... levers must be fully opened out and in the tractor seat, or to the left out of the console. Refer to start the tractor engine. These hinged levers pivot outward to open space to permit the operator to either sit in the neutral position to Operation for instructions on the front/right of the...
Operation Manual - Page 13
... crankshaft.
Release the key immediately when the engine starts
NOTE: To prevent accidental starting and/or battery discharge, remove the key from the tractor.
Towing the tractor with the throttle/choke control in use. The fuel cap is not in the fast position (full throttle) when the tractor is being driven and the mower deck is located at...
Operation Manual - Page 14
... to the "DISENGAGED" position. This indicator also illuminates when the ignition switch is turned to the "START" position and the RH and/or LH drive control levers are completed according to the right of maintenance intervals for two hours (from 50-52, 100-102, 150-152, etc.).
The display then changes to the "ON" position, the battery indicator light briefly illuminates...
Operation Manual - Page 15
...seat: Shut off the PTO, move the RH and LH drive control levers fully outward in place. Keep all shields in the neutral position, shut off the engine and remove the ignition key. Do not use... Contact your tractor efficiently.
• This engine is disengaged.
• The safety interlock system will shut off the PTO and the mower blades will change the balance of 87 or higher.
&#...
Operation Manual - Page 16
...) Position
Ignition Switch
Figure 5-1 3. Turn the ignition key to the booster battery's negative terminal;
Use fresh winter grade fuel.
then connect the other cable to the stop the engine. Start the disabled tractor following the normal starting .
however, do not keep trying to enrich the fuel mixture, except as the engine starts; If the battery indicator light...
Operation Manual - Page 17
... terrain or a hill may result in the neutral position, refer to Maintenance & Adjustments for a minimum of 30 minutes. Section 5 -
Carefully practice maneuvering the tractor using your hands.
4. Avoid sudden starts, excessive speed and sudden stops.
3. Move the throttle control lever forward to the practice area. The tractor will start to Figure 5-2. See Figure 5-3.
1. Refer to move...
Operation Manual - Page 18
... sharper the tractor will start to move the turn ," move in the reverse direction. Driving the Tractor In Reverse
WARNING! Figure 5-5
3. Forward Left Turn
4. To turn to the left, move the levers to the neutral position to attain the desired speed, or move the left lever. Neutral Position
Slower
Faster
Figure 5-4 2.
See Figure 5-6. As the control levers are pushed...
Operation Manual - Page 19
... of the left while traveling in the direction of the forward control lever.
1. NOTE: Making a "pivot turn" on grass will turn.
4.
Operation
19 The tractor will cause severe turf defacement.
1. To turn to the neutral position, while moving the other .
Figure 5-10
Section 5 - Executing a Zero Turn
WARNING! Stop the forward or reverse motion of the tractor by...
Operation Manual - Page 20
... a slope, start at full speed will affect the quality of the strip, slow down . Align the mower with an edge of the tractor.
2.
Make certain the area to the disengaged position.
3.
A U-turn is recommended unless a pivot or zero turn the ignition key off and remove the key.
• Doing so will disengage when both drive control levers to the neutral position to...
Operation Manual - Page 21
... .
4. Move both control lever slowly into the slow reverse position; Section 5 - Lift upward from the operator's seat. the PTO should disengage and the mower deck should stop . To check the safety circuits, proceed as designed, contact you Cub Cadet dealer to the engaged position. Momentarily turn the ignition switch to the neutral operating position.
Checking the Safety...
Operation Manual - Page 22
...prevent unintended starting. Repeat the previous steps to all engine maintenance intervals, procedures, specifications and instructions. features may
differ from around the spindle pulleys 4. Before performing any maintenance or repairs, disengage the PTO, move the drive control levers fully outward in the neutral position, engage the parking brake, stop the engine. Lubrication
• Using...
Operation Manual - Page 25
... the engine off, remove the ignition key and engage the parking brake before front to fix the control lever in the desired height setting. If they are an anti-scalp feature, and should be approximately 1⁄4-1⁄2" above procedure to help adjust the other when in the neutral position. Rotate the blade nearest the...
Operation Manual - Page 26
...riding mower should be prepared for a few minutes to draining fuel.
3. NOTE: Use of...turns to spread the oil evenly on blocks to be drained of water will result in shortened life and reduce serviceability.
5.
Fully charge the battery, lower riding mower...for storage. Jack the mower up spray paint. Start the engine and allow...an open flame, spark or pilot light as STA-BIL® and ...
Operation Manual - Page 32
... any maintenance, place the PTO switch in the neutral position. Reinstall the deck (refer to 70-90 ft. Service See Figure 7-14. See your authorized dealer.
Remove the deck from the switch. Mower Blade Care
WARNING! When servicing the mower deck, be removed and special tools used in breaking loose the hex nut securing the...
Parts Manual - Page 1
Illustrated Parts Manual
Mustang RZT Riding Tractor
Printed In USA
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-03560 (Oct, 2007)
Parts Manual - Page 5
TroyBilt Mustang 50" RZT
Electrical
Ref. Tapp, 1/4-20 x .375 Screw, Hex Cap, 1/4-20 x .75 GR5 Nut, Hex Sems, 1/4-20 Meter, Hour Switch, Dbl. Brake/Rev Solenoid Switch, Outer Seat Spring Switch, Inner Seat Spring Key Battery, 235 CCA Plate, Insulator Boss Plate, Insulator Tie,...
Screw, Hex Wash. Part No. Neutral Switch, PTO Switch, Ignition Switch, Interlock, (NO/NC) - Pole - Hd.
Parts Manual - Page 9
TroyBilt Mustang 50" RZT
Operator's Controls
Ref. Part No. No.
1 603-04160B 2 603-04387 3 603-04388 4 647-04065 5 647-04099 6 703-... 747-04637 42 748-04169
Description
Shaft Assembly, Deck Lift Lever, Lapbar, RH Lever, Lapbar, LH Rod, Brake Shaft, Damper Control Bracket, Lapbar Pivot Handle, Brake Bracket, Deck Hangar Arm, Deck Lift Bracket, Actuator Link, Deck Lift Screw, Hex Cap Lock...
Parts Manual - Page 11
...Hd. No
Description
1 603-04328A Housing, Deck
777S32598
Graphic, Danger
777S30503
Graphic, Danger
777I22282
Graphic, Instruction
777D11833 Graphic, 50"
2 618-04125A Spindle Assembly
3 631-04070A Chute Assembly, Discharge
777S30284
Graphic, Danger
4 683-0254 Bracket, Deck Hanger... 732-0459 Spring, Extension, .94 Dia. TroyBilt Mustang 50" RZT
11
Mower Deck
Ref. Part No. Hd.
Similar Questions
Troy Built Riding Mower Turn Key And It Clicks Starter Motor Not Seized ?do
Mower tb30 b Turn key and clicks starter not siezed
Mower tb30 b Turn key and clicks starter not siezed
(Posted by rusthumphrey 1 year ago)
Our Walk Behind Runs Then Stop It And It Won't Start
our Troy-bilt TB210 will run great when started cold any time of the year but if have to shut it off...
our Troy-bilt TB210 will run great when started cold any time of the year but if have to shut it off...
(Posted by WaltDasy 7 years ago)
Belt Coming Off
new belt installed good on lowest cutting setting comes loose and off on any higher setting.
new belt installed good on lowest cutting setting comes loose and off on any higher setting.
(Posted by ishinethrou24 8 years ago)
What Oil Filter Should I Use On Mustang 50 Zero Turn Mower
(Posted by Clcneale 9 years ago)
There Is Minimal Response With The Right-hand Control Lever. How To Adjust?
There is minimal response with the Right-hand Control lever. How to adjust? Is there a good video wh...
There is minimal response with the Right-hand Control lever. How to adjust? Is there a good video wh...
(Posted by RMorrow53 9 years ago)