TP-Link TL-WA5210G Support Question
TP-Link TL-WA5210G Support Question
Find answers below for this question about TP-Link TL-WA5210G.Need a TP-Link TL-WA5210G manual? We have 1 online manual for this item!
Question posted by henrrybrain on May 10th, 2014
Capability
How many users can connect to a TL-WA5210G at a time. And also does it go upto 5 kilo meter radius? Please let me know how many users that can connect to the router at the same time.ThanksHenry
Current Answers
Related TP-Link TL-WA5210G Manual Pages
TL-WA5210G V1 QIG 7106503701 - Page 1
... the two CPEs are using an external antenna to connect, please refer to face, otherwise the wireless signal strength might be weak. Here shows several incorrect examples. Note If you are placed face to Appendix 1. 1 1 Typical network
TL-WA5210G is used for TL-WA5210G is shown as above.
Note The typical connection for remote point-to-point...
TL-WA5210G V1 QIG 7106503701 - Page 2
... not obstruct the antenna signals and which offers maximum line-of the Power Injector to a PC using another Ethernet cable. Then, connect the LAN port of -sight propagation with the users.
Finally, plug the provided power adapter into the DC jack on the back of the CPE and then around the pole...
TL-WA5210G V1 QIG 7106503701 - Page 3
... CPEs to build the network, please make sure that the two CPEs are placed face to the figure below after the above steps are well connected to your network devices and then check to see if all your device. 3
Turn on the AP display normally as the diagram below describes. The...
TL-WA5210G V1 QIG 7106503701 - Page 4
... and press Enter A dialog box will prompt you forget the password.
Enter the default values and click OK. T2 will display after successfully logging in. User name: admin Password: admin
Click OK
Note If the dialog box does not pop up, please refer to assign your web browser and type http...
TL-WA5210G V1 QIG 7106503701 - Page 5
... to set it as a router, please choose AP Router mode, and for AP Client Router Mode
This page will then display. A. Choose your WAN Connection Type provided by your WISP, please choose AP Client Route2r
mode and proceed to AǗ
b) If you want to set up a point-to-point connection with TL-WA5210G, please skip to your...
TL-WA5210G V1 QIG 7106503701 - Page 6
...Click Finish
B. Enter the SSID provided by network users. Click Finish
6 Configuration for example Select your wireless network; Here we enter TP-LINK_900008 as the ...however, choose a name that is easily remembered by your WISP
Click Next
Click Finish to -Point Connection Note Two TL-WA5210Gs are needed for this application. 1) The AP Setting
Select AP
Click Next
Enter a unique name for...
TL-WA5210G V1 QIG 7106503701 - Page 7
....168.1.2 as an example.
C. Click Wireless > Wireless Mode Select Client Enter TP-LINK_900008, the SSID of the first AP you click Save.
7
Click Operation Mode Select AP
Click Save
The AP will begin rebooting automatically after you click Save. Configuration for Repeater To make sure the TL-WA5210G is under AP mode, please follow...
TL-WA5210G V1 QIG 7106503701 - Page 8
... get a better signal strength according to repeat, and then click Connect on the Antenna Alignment page.
Note The BSSID is the same as the MAC address.
Click Wireless Click Antenna Alignment
8 Then click Save at the bottom of the line. Click Wireless > Wireless Mode Select Repeater
Click Survey This page will then display. Antenna...
TL-WA5210G V1 QIG 7106503701 - Page 9
... external antennas, you need to assign your computer a Static IP address within the same range as the following steps:
Connect one side of the TL-ANT24SP to the RP-SMA port of the TL-ANT24SP to use TP-LINK products for outdoor solution. See the Troubleshooting T3 if you are recommended to the...
TL-WA5210G V1 QIG 7106503701 - Page 10
User name: admin Password: admin
Click OK
Configure the external antenna
Click Wireless Setting
Select External
Click Save
'
10 Login
Open your web browser and type in http://192.168.1.254 in the address bar and press Enter A dialog box will prompt you for the User name and Password. Enter the default values and click OK.
TL-WA5210G V1 QIG 7106503701 - Page 11
... 2) Use the default user name and password: admin, admin; 3) Try to Start > Control Panel, you will then see the following the instructions of this QIG. If you don't know
how to do if...Network and Internet Connections
11
For Windows XP OS Go to reconfigure your computer's IP Address. How do if I forget my password? 1) Restore the AP's configuration to reconfigure the router. With the ...
TL-WA5210G V1 QIG 7106503701 - Page 14
Click Change adapter settings
Right-click Local Area Connection Click Properties
Double-click Internet Protocol Version 4 (TCP/IPv4)
14
TL-WA5210G V1 QIG 7106503701 - Page 16
...to: www.tp-link.com/support/faq.asp
„ To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp
„ For all other technical support, ...link.com Fee: 4-8 Rp/min, depending on rate of different time Service time: Monday to Friday
9:00 AM to 6:00 PM GMT+ 1 or GMT+ 2 (Daylight Saving Time)
Australia & New Zealand Tel: AU 1300 87 5465
NZ 0800 ...
Similar Questions
Connecting To Wireless Network With Cpe Tl-wa5210g, Can Chage Mac Adress?
(Posted by sundactvos 9 years ago)
Tl-wa5210g After Configured As Repeater My Pc Cannot Connect Via Wireless
(Posted by reylizraine 12 years ago)