TP-Link TD-8816 Support Question
TP-Link TD-8816 Support Question
Find answers below for this question about TP-Link TD-8816.Need a TP-Link TD-8816 manual? We have 2 online manuals for this item!
Question posted by marceloarrj on July 15th, 2011
How To Make Remote Access To Device Managemer From Web (wan)?
I'm getting trouble to make access to my TD8816 from WAN side. If I type its IP in my browser inside my LAN, everything runs OK, but when I try from the internet, for example via 3G modem, I can't access it from external IP.
I tried yet, to change ACL settings even to free all from both sides, and disabled it to without success.
I'm using DynDNS to, it gets my externa IP correctly, but doesn't connect.
Someone could help me:
Current Answers
Related TP-Link TD-8816 Manual Pages
User Guide - Page 7
... ADSL Internet connection for the configuration. The Router is made using a single Wide Area Network (WAN) interface and single global IP address. ADSL
The TD-8816 supports full-rate ADSL2+ connectivity conforming to use. TD-8816 ADSL2/2+ Ethernet Router User Guide
Chapter 1. Introduction
Thank you for choosing the TD-8816 ADSL2/2+ Ethernet Router .
1.1 Product Overview
The device is...
User Guide - Page 10
... desktop.
2.4 Connecting the Router
Before installing the device, please make calls at the same time. Method two：You can access the Internet and make sure your broadband service provided by your ISP is any problem, please contact your ISP. You can follow the steps below to the ADSL LINE port of TD-8816 Plug one end of...
User Guide - Page 24
... 4-9). Bridges are two segments of the same physical LAN. TD-8816 ADSL2/2+ Ethernet Router User Guide Subnet Mask and Gateway IP address. ¾ Default Route: You should select Yes to configure the PVC as if they are devices that enable two or more networks to communicate as the default gateway to internet from this type of connection, the modem can...
User Guide - Page 25
... the Internet. • IP Address: Enter the Router's local IP Address, then you can access to the Web-based
Utility via the IP Address, the default value is 192.168.1.1. • IP Subnet Mask: Enter the Router's Subnet Mask, the default value is a session-layer protocol used to specify the RIP (Routing Information protocol)
version for the device. The Router will...
User Guide - Page 33
... incoming packets, QoS determines which is useful when there are certain types of selected network traffic over various technologies. TD-8816 ADSL2/2+ Ethernet Router User Guide Click the Back button to return to prioritize data as voice data packets give higher priority than Web data packets. This option will provide better service of data you...
User Guide - Page 38
... the Router
remotely. The feature makes it . ¾ Interface: Select the interface for access: LAN, WAN or Both. ¾ Access Control of Listing: This displays the information about the ACL Rules.
4.5.2 Filter
Choose "Access Management→Filter", you can see the Filter screen (the default is IP/MAC Filter screen shown in ). IP Filter Select IP/Mac Filter as the Filter type...
User Guide - Page 39
....
33 Selecting Both, the IP traffic from LAN and WAN are three filtering directions: Both,
Incoming, Outgoing.
) Note:
Selecting Outgoing, the filtering feature only allows some IP traffic from LAN to access to some specifically addresses; There are both blocked. TD-8816 ADSL2/2+ Ethernet Router User Guide
Figure 4-27 ¾ Filter Type Selection: Select the filter type for the next...
User Guide - Page 40
... example: If you select Next, the router will
skip the rule and transmit directly. You can enter 0, it means
that all IP addresses are (1, 1), (1, 2) and (1, 3). You can configure the rules as the Filer Type Selection (show in the Filter List) for the rule. Step 1: Select the "IP/MAC Filter" as follows. And wish to make the...
User Guide - Page 42
... rule and transmit directly. Step 1: Select the "IP/MAC Filter" as the Filer Type Selection:
Select the "MAC" as follows. TD-8816 ADSL2/2+ Ethernet Router User Guide
Figure 4-28 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select "Yes" to make the rule to match. ¾ IP/MAC Filter Listing: This displays the information...
User Guide - Page 49
... Time Protocol) server. TD-8816 ADSL2/2+ Ethernet Router User Guide
Figure 4-36
) Note:
1) There is only one account that can configure the system time in the screen (shown in Figure 4-36). The system time is "admin". NTP Server automatically Select NTP Server automatically as the Synchronize time, you can access Web-Management interface. Figure 4-37...
User Guide - Page 7
... conforming to an Ethernet LAN or computers via standard Ethernet ports. TD-8816 ADSL2/2+ Ethernet Router User Guide
Chapter 1. The ADSL connection is designed to 6.5Km. ¾ Supports remote configuration and management through local Ethernet using any web browser. The device is made using a single Wide Area Network (WAN) interface and single global IP address. In addition to...
User Guide - Page 24
... the parameters for the device.
These
settings may change the LAN IP address if needed. TD-8816 ADSL2/2+ Ethernet Router User Guide If you select this type of connection, the modem can be configured to communicate as if they are two segments of the LAN interface for LAN ports according to as Private settings. Bridges are the IP settings of the same...
User Guide - Page 25
... to establish membership in a multicast group. TD-8816 ADSL2/2+ Ethernet Router User Guide Internet. • IP Address: Enter the Router's local IP Address, then you will see the screen below (shown in RIP2 format, the difference is that will not send RIP packet. The DHCP Server gives out IP addresses when a device is for LAN interface, including RIP1, RIP2-B and...
User Guide - Page 30
... machine to the outside world even though NAT makes your whole inside network appear as Start port number. For VCs with single IP will be added to the corresponding field automatically,...IP
Address Mapping for this VC. TD-8816 ADSL2/2+ Ethernet Router User Guide The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make...
User Guide - Page 32
.../Deactivated the IP QoS on different types (IP ToS and
26 Figure 4-20 ¾ QoS: Select this option to incoming packets, QoS determines which is useful when there are certain types of selected network traffic over various technologies. TD-8816 ADSL2/2+ Ethernet Router User Guide Click the Back button to return to give higher priority than Web data...
User Guide - Page 37
... feature makes it . ¾ Interface: Select the interface for access: LAN, WAN or Both. ¾ Access Control of Listing: This displays the information about the ACL Rules.
4.5.2 Filter
Choose "Access Management→Filter", you can see the Filter screen (the default is IP/MAC Filter screen shown in Figure 4-27), then you can
access to the Router. TD-8816 ADSL2/2+ Ethernet Router...
User Guide - Page 38
... Selecting Both, the IP traffic from LAN and WAN are three filtering directions: Both,
Incoming, Outgoing.
) Note:
Selecting Outgoing, the filtering feature only allows some IP traffic from LAN to access to some specifically addresses. This index can be
32 TD-8816 ADSL2/2+ Ethernet Router User Guide
Figure 4-27 ¾ Filter Type Selection: Select the filter type for the next configuration...
User Guide - Page 39
TD-8816 ADSL2/2+ Ethernet Router User Guide allowed by setting up filters. ¾ IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry.
) Note:
You should set the IP/MAC Filter Set Index and IP... TCP, UDP or ICMP for the IP Filter rule. You can configure the specific rule for the example. Step 1: Select the "IP/MAC Filter" as the Rule Type on your local network; If you...
User Guide - Page 41
TD-8816 ADSL2/2+ Ethernet Router User Guide
Figure 4-28 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select "Yes" to make the rule to take effect. ¾ MAC Address: Enter the MAC address for the example.
Step 1: Select the "IP/MAC Filter" as the Filer Type Selection:
Select the "MAC" as follows. Presume the rules...
User Guide - Page 48
... used by the device for scheduling services. There are three methods to set Daylight Saving dates and the system time will only need to set , you can access Web-Management interface. NTP Server automatically Select NTP Server automatically as the Synchronize time, you may also set the time zone. TD-8816 ADSL2/2+ Ethernet Router User Guide...
Similar Questions
How To Configure The Access Control On Adsl Router Td-w8951nd
(Posted by jarppluci 10 years ago)
How To Access Management Instruction Tp-link Router Td-w8951nd
(Posted by steMD 10 years ago)
Difficulty Accessing Settings
Accessing modem settings via 192.168.1.1 used to work by using 'admin' in both the username and pass...
Accessing modem settings via 192.168.1.1 used to work by using 'admin' in both the username and pass...
(Posted by dasprem 12 years ago)
Access Point & Repeater
i want configure tp-link access point & repeater (16 repeater) in hotal make a wireless networkin...
i want configure tp-link access point & repeater (16 repeater) in hotal make a wireless networkin...
(Posted by ramshivtm 12 years ago)