Sony PDM-4210 Support Question
Sony PDM-4210 Support Question
Find answers below for this question about Sony PDM-4210 - Plasma Display Panel.Need a Sony PDM-4210 manual? We have 1 online manual for this item!
Question posted by 2bad4uimkc on April 28th, 2019
Why Dose The Standby Light Flash And I Can't Turn Tv On
Why dose the standby light flash and I can't turn TV on
Requests for more information
Request from thomasn794 on January 25th, 2021 8:11 PM
The Green ligher and red is flashing in stand by mode
The Green ligher and red is flashing in stand by mode
Current Answers
Answer #1: Posted by NicoleN2306 on April 29th, 2019 4:27 AM
NicoleN2306
Member since:
April 26th, 2019 Points: 3,900
Member since:
April 26th, 2019 Points: 3,900
- If a Red LED is blinking and the TV is not working properly it means that the TV has detected an issue or problem. Most Red LED blink conditions require service. The meaning of the blink codes differs between TV models, but the following steps may resolve user serviceable errors related to heat, temporary conditions, or software updates:
NOTE: 8 Times Blink - For certain models, a special reset procedure is needed if the Red LED on the front of the TV is blinking 8 times and then repeats. This is a model-specific issue that may be resolved by following these steps (please check the answer to be sure your model is included).
For other TV models or other Red LED blink codes:
- Turn the TV off and back on. If the TV will not respond to the remote or the power button, or if that does not fix the issue, unplug the TV. For a Projection TV or Projector , leave it off for 3 minutes. For other TVs leave it off for 1 minute. Plug the TV back in and turn it on.
NOTES:- If the TV is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
- Projection TVs and projectors need to cool down before they will turn on again. You may need to wait several minutes before these will turn back on.
- Clean any vents/slots in the TV cabinet and make sure there is room for air to circulate around the cabinet of the TV.
- Some Sony TVs have a media box (tuner) and separate display. If you have one of these TVs, check to make sure the cable between the media box and the display is securely connected.
- For Projection TVs and Projectors, make sure that the cover/door for the lamp is closed and secure.
- If the TV can be operated at all, check to see if a software update is available.
- If your TV is connected to the Internet, press the Home or Menu button on the remote to get into the setting menus. The Software Update option is usually found under the Product Support or Contact Sony menu.
- NOTE: For a limited number of Internet-capable models, the only option is to turn on Automatic Software Updates and allow the TV to update on its own. If you only have this option, make sure it is set to On. Automatic updates are only downloaded when the TV is in standby mode (turned off with the remote but not unplugged). Normally this download will happen overnight but may take up to 24 hours.
- You can check to see if a software (firmware) update is available for your television. Steps to install will be included if an update is available.
- Older CRT TV's and TV's that cannot be connected to the Internet do not have an option to check for a software update or may not capable of being updated.
- Turn the TV off and back on. If the TV will not respond to the remote or the power button, or if that does not fix the issue, unplug the TV. For a Projection TV or Projector , leave it off for 3 minutes. For other TVs leave it off for 1 minute. Plug the TV back in and turn it on.
- If these options do not resolve the issue, the problem is most likely related to an internal component that must be replaced and service will be required.
Related Sony PDM-4210 Manual Pages
Child Safety: It Makes A Difference How and Where You Use Your Flat Panel Display - Page 1
... pulled over and cause injury. Flat panel displays can be mounted to walls with furniture and television sets. • Don't place flat panel displays on your flat panel display.
• Carefully read and understand all...; The home theater entertainment experience is a growing trend and larger flat panel displays are inappropriately situated on or play with steel studs or old cinder block...
Similar Questions
Como Consigo Un Control Remoto Para Tv Sony De Plasma Modelo Pdm-6110? Gracias!!
(Posted by juanlibrado1 1 year ago)
Blinky Light
how do I get this tv to turn on what is required to make it work it just blinks a red light.
how do I get this tv to turn on what is required to make it work it just blinks a red light.
(Posted by kiethunwatkins7890 4 years ago)
Where To Get Cable Television Plasma Model Pdm - 5010 Eclusive Sony Help Me.
where to get cable television plasma model PDM - 5010 exclusive sony help me email meq.queiroga@hotm...
where to get cable television plasma model PDM - 5010 exclusive sony help me email meq.queiroga@hotm...
(Posted by meqqueiroga 8 years ago)
I Lost My Remote How Do I Turn Tv On Thers No Power Button
(Posted by ibarela46 8 years ago)
Cable For Sony Pdm4210 Plasma Television
I have a Sony plasma television that was wall mounted and when it was taken off the wall, the cable ...
I have a Sony plasma television that was wall mounted and when it was taken off the wall, the cable ...
(Posted by rosannaverrengia 10 years ago)