Singer Futura XL-400 Support Question
Singer Futura XL-400 Support Question
Find answers below for this question about Singer Futura XL-400.Need a Singer Futura XL-400 manual? We have 1 online manual for this item!
Question posted by sasqueen on March 17th, 2015
Where Can I Find A Replacement Cd-rom? Or, Can I Download The Info?
The person who posted this question about this Singer product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Brainerd on March 17th, 2015 11:29 PM
Brainerd
Member since:
May 24th, 2014 Points: 759,620
Member since:
May 24th, 2014 Points: 759,620
Hi, please use the info here to order a replacement:
Phone: 800-474-6437
How to reach a live person:
This is a direct number to a live customer service rep
Hours of Operation:
Mon-Fri: 8am-4pm CT
I hope this helps you!
Please press accept to reward my effort or post again with more details if not satisfied.
Regards, Brainerd
Related Singer Futura XL-400 Manual Pages
Instruction Manual - Page 2
...." 20.
"Read all moving parts. "Use this can cause needle to the nearest authorized dealer or service center for its affiliates.
"CAUTION-- "This sewing machine should always be replaced by or near children." 2. Unplug the foot controller of the appliance by the manufacturer as threading needle, changing
needle, threading bobbin, or changing presser...
Instruction Manual - Page 5
... Stitching 48 - 49 Continuous patterns 50 - 51 Sewing on a button 50 - 51 Buttonholes 52 - 57
Using buttonhole foot, Procedure, Corded buttonholes Buttonholing with Futura Multi hoop 88 - 95 Helpful messages when embroidering 96 - 97
4. TABLE OF CONTENTS
1.GETTING TO KNOW YOUR MACHINE Machine identification 6 - 7 Accessories 8 - 9 Setting up your machine 10 - 11 Spool pins 10 - 11...
Instruction Manual - Page 10
...)
7. Screwdriver (large)
11. Thread spool net (short)
The Foot that comes on your
7
Sewing machine is called the
General Purpose Foot and will
be
used for most decorative sewing. Bobbins 21. Scissors 22. To install the FUTURA software, refer to the CD insert for needle plate
10. Spool pin cap (large)
8. Buttonhole opener/Brush
9. Zipper...
Instruction Manual - Page 12
... Connecteur de la machine Conector de la máquina
2 1
Pin Butée Pasador
3
Power line cord Cordon Cordón de la linea eléctrica
Foot control Rhéostat
XL-550-P04-1.Ceonptrsol por pedal
Power/light ... a spool cap to wipe off any surplus oil from needle plate area before using sewing machine only.
Place felt disc over it. Place a thread spool on . Spool Bobine Carrete...
Instruction Manual - Page 16
... rotate counterclockwise when thread is a very important step. With a finger held gently on the top left .
5. THREADING THE BOBBIN THREAD
1.
Replace the clear bobbin cover plate onto the needle plate. NOTE: Sewing can be started without having to remove the cover.
3. A
Cutter Coupeur Cortador
Groove Cannelure Surco
B
A
14 Remove the bobbin cover...
Instruction Manual - Page 24
...
Lower the presser foot lifter so that the foot holder snaps
on top of the machine.
A balanced tension (identical stitches both top and bottom) is largely determined by the ...sewing will be less than that for straight stitch sewing. BOBBIN TENSION
The bobbin tension has been correctly set thread tension at the factory, so you find that the machine is irregular, you are sewing...
Instruction Manual - Page 28
...Width / Needle Position Control Knob.
At each of the potential adjustments. Width setting for twin needle sewing can be activated if it is activated.
26 Auto (preprogrammed) default settings are at default settings of... width/needle position controls
*Auto/Default settings Your sewing machine will produce most of your preference. The LED Indicator next to move the control knobs while...
Instruction Manual - Page 30
... slowly, and when the button is used, the lever serves as a top speed limiter.
6
28 The sewing machine makes 4 tiny tacking stitches to start.
Red light indicates machine is pushed.
2
2. The position of other stitches Fonction de point de faufilage pour la jonction avec d'autres points Función de remate para terminaci...
Instruction Manual - Page 34
...fabric, slight "fine tuning" of
3
the machine, leaving about 6" (15 cm) clear.
3. Thread tension control B. Tacking stitch mode button C. Start/stop the sewing machine. Pull both Metric and Inch Markings as ....
5. The numbers indicate distance from the needle at rear side) G. Start the machine. KEEPING SEAMS STRAIGHT
To keep the seam straight, use one of the numbered guide ...
Instruction Manual - Page 54
Select one buttonhole patterns. Replace the presser foot with the selected button.
1.
Insert the ...practice buttonhole on a scrap of the button. tab B Languette B Lengüeta B
2. It is helpful to remove the extension table when sewing a buttonhole, to "Using buttonhole foot" above.)
4. BUTTONHOLES USING BUTTONHOLE FOOT
1. tab A Butée A Lengüeta A
PROCEDURE
...
Instruction Manual - Page 56
...position Position d'alignement du pied boutonnière Posición de alineación del pie de ojaladora When sewing is finished, use a buttonhole opener to a length of buttonhole on the buttonhole foot, and then lower ... the fabric under the foot. While holding the top thread, start the machine. Be careful not to the rear.
7. Align the buttonhole mark on the fabric with the mark on your ...
Instruction Manual - Page 60
... foot Pied presseur de broderie Prensatelas de bordado
58
Turn hand wheel toward you to machine CAUTION before changing presser foot.
* Raise presser foot lifter. INSERTING THE BOBBIN
Refer... EMBROIDERY SEWING
BEFORE ATTACHING EMBROIDERY UNIT ATTACHING EMBROIDERY FOOT
Foot holder Support du pied Sujetador prensatelas
Always be sure to touch the needle when CAUTION replacing presser ...
Instruction Manual - Page 64
... slide toward the left to the embroidery unit. REMOVING EMBROIDERY UNIT
* Turn off the machine. Holding handle of the embroidery unit and pull it clicks into place.
Doing so may... unit is not securely installed, the finished embroidery may cause CAUTION damage to close for general sewing.
3
Handle Poignée Mango
1
Release lever Support de cerceau Palanca de liberación
...
Instruction Manual - Page 74
... select the directory where the software should be installed.
If after a short while, the software doesn't automatically start automatically. This procedure is "D:"
Please insert the FUTURA CD-ROM into the CD-ROM disc receiver in the License Agreement, please click on "Yes", and again click on "Next" to continue.
72
Instruction Manual - Page 76
... a design to work with the installation. Next attach the embroidery unit to 100%. Turn off your sewing machine.
Please wait for proper start the copy and installation of available space on your desktop to open the Futura software. You are not followed precisely, you will prompt you .
2.
You can always abort the installation...
Instruction Manual - Page 90
...sultat final de la broderie. A single hoop appears on cross lines that each other . and then sews them precisely, matching one section to the other .
When these points are input on the screen marked...Hooping is a special feature in the Futura software that will allow embroidery data which is larger than a single embroidery hoop to be sent to the machine to stitch out, while making it ...
Instruction Manual - Page 100
... dog control Abaisse-griffe d'entraînement Control de dientes
CONVERTING TO FREE-ARM SEWING
Your machine can be raised for all general sewing purposes and lowered for darning, freehand embroidery and monogramming so that is being sewn. To replace, slide the extension table back into a slim free-arm model for your presser foot...
Instruction Manual - Page 102
... - Fabric does not move. * Presser foot is being pulled or pushed against machine feeding
action. - Lengthen stitch length. (see page 20
- 21). * Needle is not raised when sewing stitch patterns.
- Stitches are lowered -
Lower buttonhole lever. (see page 98 - 99). Replace needle. (see page 102 - 103). Clean hook. (see page 20 - 21). Needle...
Instruction Manual - Page 104
... all purpose" oil as illustrated for sewing machine lubrication.
5. Use dry rags to its highest position and put
6
and slide the needle plate into position as indicated by removing the plug from the sewing machine and footcontroller. Raise the needle to remove dust from the wall-outlet.
Replace the bobbin case with the lint brush...
Instruction Manual - Page 106
... arrows.
1 Face cover Plaque frontale Cubierta frontal
Helpful Hints : For the machine used after a long interval : It should be oiled before oiling.
For best results always use SINGER Brand Sewing Machine Oil. For the machine used frequently : It should be oiled periodically. Use of sewing machine oil to your machine. Screw Vis Guia
2
Screw Vis Guia
104
Similar Questions
Replacement Part For Singer Futura Xl 400
I am looking for the embroidery arm unit for a Singer Futura Xl 400. Can you assist me in locating t...
I am looking for the embroidery arm unit for a Singer Futura Xl 400. Can you assist me in locating t...
(Posted by sjh4ba 3 years ago)
Singer Futura Xl-400
I am in need of a Singer Futura XL-400 Startup disc. Any idea where I can get one
I am in need of a Singer Futura XL-400 Startup disc. Any idea where I can get one
(Posted by fayevb 4 years ago)
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)
How Do I Install Auto Punch Into My Singer Futura 400 Programme
Do I have to link my sewing machine with the computer before installing Auto Punch. No joy so far.
Do I have to link my sewing machine with the computer before installing Auto Punch. No joy so far.
(Posted by jchurn33 11 years ago)